|
|
|
 |
|
|
|
New product design and development is more often than not a crucial factor in the survival of a company. In an industry that is fast changing, firms must continually revise their design and range of products. This is necessary due to continuous technology change and development as well as other competitors and the changing preference of customers. Sensor technology plays an important role in the research and development of new products and in the process to develop solutions to unique problems. |
|
|
 Products |
| |
 | 1203 Triaxial Crash Test Accelerometer
The Model 1203 Accelerometer is a small, compact triaxial device designed for vehicle impact and road testing. Available in ranges from 50g to 1000g. |  | 1207 Crash Test Accelerometer
The Model 1207 accelerometer is a small, compact uniaxial device designed for vehicle impact and road testing. This device features a rugged strain relief. Available in ranges from 50g to 1000g. |  | 1207F Crash Test Accelerometer
The Model 1207F accelerometer is a small, compact uniaxial device designed for vehicle impact and road testing. This device features a rugged strain relief. Available in ranges from 50g to 1000g. |  | 201 Accelerometer
The Model 201 is a low noise accelerometer offering both static and dynamic response. The accelerometer is packaged in an anodized aluminum housing with an integral cable. It is offered in ranges from ±2g to ±50g. |  | 3700 Shock Accelerometer
The Model 3700 is a MEMS piezoresistive shock accelerometer in a rugged stainless steel package. Available in ranges from ±50g to ±6000g. |  | 3801A Accelerometer
The Model 3801A is a mV output piezoresistive accelerometer in a rugged hermetic package. Available in ranges from ±2g to ±2000g. |  | 4001A Accelerometer
The Model 4001A is an economical signal conditioned accelerometer with integral temperature compensation. The accelerometer incorporates an integral 5-pin connector at the end of the cable assembly. Available in ranges from ±2g to ±200g. |  | 4002 Accelerometer
The Model 4002 is a low frequency DC response accelerometer with exceptional resolution. The accelerometer is designed for optimum signal-to-noise ratio and offers an amplified signal conditioned output. Available in ranges from ±2g to ±200g. |  | 4202 Biaxial Accelerometer
The Model 4202 Biaxial Accelerometer is designed with performance and reliability in mind. A heavy-duty shielded cable and an EMI/RFI module protects the accelerometer from the harsh operating environments. Available in ranges from ±6g to ±30g. |  | 4203 Triaxial Accelerometer
The Model 4203 Triaxial Accelerometer is designed with performance and reliability in mind. A heavy-duty shielded cable and an EMI/RFI module protects the accelerometer from the harsh operating environments. Available in ranges from ±6g to ±30g. |  | 4600 Accelerometer
The Model 4600 is designed for both static and dynamic measurements in critical and demanding applications. It is hermetically sealed and features high-g shock protection. Provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4602 Accelerometer
The Model 4602 is designed for both static and dynamic measurements in critical and demanding applications. The accelerometer offers outstanding thermal performance over the complete operating range from -54°C to +121°C. Provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4604 Accelerometer
The Model 4604 is a rugged, low-profile MEMS accelerometer designed for both static and dynamic applications. The device offers outstanding thermal performance and features a robust strain relief and cable. Provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4605 Accelerometer
The Model 4605 is designed for both static and dynamic measurements in critical and demanding applications. The device offers outstanding thermal performance and features a detachable cable. Provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4610 Accelerometer
The Model 4610 is a low noise signal conditioned accelerometer with exceptional long-term stability. The accelerometer offers integral temperature compensation and a hermetically sealed sensor assembly. Provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4620 Accelerometer
The Model 4620 is a low frequency DC response accelerometer offering outstanding performance over a wide operating temperature range. The device incorporates a Teflon insulated cable with a rugged strain relief designed for demanding applications. Provides an amplified output. Available in ranges from ±2 to ±250g. |  | 4623 Accelerometer
The Model 4623 is a low frequency DC response accelerometer offering outstanding performance over a wide operating temperature range. The device features EMI/EMC protection circuitry and a rugged strain relief for harsh installations. Provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4630 Triaxial Accelerometer
Low noise; static & dynamic response. The 3 circuit assemblies are hermetically sealed. Operates on common or separate power supplies. Ranges from ±2 to ±500g. |  | 4632 Triaxial Accelerometer
The Model 4632 is a low noise triaxial accelerometer offering both static and dynamic response. The accelerometer is packaged in an anodized aluminum housing. Provides amplified outputs for each axis. Available in ranges from ±2 to ±200g. |  | 4801A Accelerometer
The Model 4801A is a true hermetically sealed accelerometer in a rugged stainless steel package. The sensor offers an amplified signal conditioned output, enhanced temperature compensation, and shock protection up to 10,000g. Available in ranges from ±2 to ±500g. |  | 4803A Triaxial Accelerometer
The Model 4803A is a low noise triaxial accelerometer in a rugged, welded stainless steel package. The silicon MEMS accelerometer incorporates integral temperature compensation and provides an amplified output. Available in ranges from ±2 to ±500g. |  | 4810A Accelerometer
The Model 4810A is a low noise signal conditioned accelerometer in a welded stainless steel package. It features a detachable cable, temperature compensation, and a signal conditioned output. Available in ranges from ±2 to ±500g. |  | 52 Crash Test Accelerometer
The Model 52 accelerometer is based on an advanced piezoresistive MEMS sensing element which offers exceptional dynamic range and stability. This unit has been designed for side impact crash applications. Available in ranges from ±50g to ±2000g. |  | 52M30 Crash Test Accelerometer
The Model 52M30 accelerometer has an advanced piezoresistive MEMS sensing element which offers excellent dynamic range and stability. This unit has been designed for side impact crash applications. Features an aluminum housing and jacketed cable. Available in ranges from ±50g to ±2000g. |  | 53 Triaxial Crash Test Accelerometer
The Model 53 accelerometer is a small, compact triaxial device designed for vehicle impact and road testing. Available in ranges from ±50g to ±2000g. |  | 63 Triaxial Crash Test Accelerometer
The Model 63 accelerometer is a small, compact triaxial device designed for vehicle impact and road testing. Its mechanical overload stops provide high shock protection in rugged applications. Featuring ranges from 500g to 2000g and frequency response to 3000 Hz, this sensor is easily mounted in hard to reach places. |  | 64 Crash Test Accelerometer
The Model 64 accelerometer is based on an advanced piezoresistive MEMS sensing element which offers exceptional dynamic range and stability. Available in ranges from ±50g to ±6000g. |  | 64B Crash Test Accelerometer
The Model 64B accelerometer is based on an advanced piezoresistive MEMS sensing element which offers exceptional dynamic range and stability. This unit is compliant with SAE J211 standards for anthropomorphic dummy instrumentation. Available in ranges from ±50g to ±6000g. |  | 64C Crash Test Accelerometer
The Model 64C accelerometer is based on an advanced piezoresistive MEMS sensing element which offers exceptional dynamic range and stability. This unit is compliant with SAE J211 standards for anthropomorphic dummy instrumentation. Available in ranges from ±50g to ±6000g. |  | 68C Crash Test Accelerometer
The Model 68C accelerometer is a small, compact triaxial device designed for vehicle impact and road testing. This unit is compliant with J211 specifications for anthropomorphic dummy applications. Available in ranges of ±50g and ±2000g. |  | 7100A IEPE Accelerometer
The Model 7100A is a high performance IEPE accelerometer with an operating temperature range of -55°C to +150°C. It is hermetically sealed and features the popular through hole mount installation. Available in ranges from ±50 to ±500g. |  | 7101A IEPE Accelerometer
The Model 7101A is a miniature, high performance IEPE accelerometer available in ±50g to ±500g dynamic ranges. The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >10kHz. |  | 7104A IEPE Accelerometer
The Model 7104A is a high performance IEPE accelerometer available in ±50g to ±500g dynamic ranges. The stud mounted accelerometer features a welded hermetic construction with a side mount 10-32 coaxial connector. |  | 7105A IEPE Accelerometer
The Model 7105A is a high performance IEPE accelerometer available in ±50g to ±500g dynamic ranges. The stud mounted accelerometer features a welded hermetic construction with a top mount 10-32 coaxial connector. |  | 7108A IEPE Accelerometer
The Model 7108A is a miniature adhesive mount IEPE accelerometer available in ±50g to ±500g dynamic ranges. The accelerometer features a welded hermetic stainless steel construction with a coaxial 10-32 top connector. |  | 7130A Triaxial IEPE Accelerometer
The Model 7130A is a triaxial IEPE accelerometer available in ±50g to ±500g dynamic ranges. The unit features a hard anodized aluminum housing, and has a flat frequency response to 9kHz. |  | 7132A Triaxial IEPE Accelerometer
The Model 7132A is a miniature triaxial IEPE accelerometer available in ±50g to ±2000g dynamic ranges. The accelerometer features a hermetically sealed titanium construction with a 4-pin Microtech connector interface. |  | 7204A IEPE Accelerometer
A case isolated high temperature IEPE accelerometer with internal shielding. Has a flat bandwidth up to greater than 15kHz with a resonant frequency greater than 40kHz. Available in ±50 to ±500g ranges. |  | 7500A Charge Accelerometer
The Model 7500A is a piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. It has charge output of 20pC/g, and provides stable thermal response up to +260°C. Available in ±250g up to ±2000g dynamic range. |  | 7501A Charge Accelerometer
The Model 7501A is a miniature piezoelectric charge mode accelerometer with an operating temperature range to +260°C. It is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >15kHz with 5.6pC/g nominal output. Available in ±2000g dynamic range. |  | 7502A Charge Accelerometer
The Model 7502A is a miniature piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. It has a charge output of 1.6pC/g, and provides stable thermal response up to +200°C. Available in ±2000g dynamic range. |  | 7508A Charge Accelerometer
The Model 7508A is a miniature piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. With a nominal charge output of 5.6pC/g the model 7508A offers a high signal to noise ratio in a miniature package. Available in ±2000g dynamic range. |  | 7514A Charge Accelerometer
The Model 7514A is a stud mounted piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. It offers a wide bandwidth to >14kHz with a nominal charge output of 50pC/g. Available in dynamic ranges of ±500g to ±2000g. |  | 7530A Triaxial Charge Accelerometer
The Model 7530A is a triaxial piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. It provides a stable thermal response up to +200°C and a nominal charge output of 5.6pC/g. Available in ±2000g dynamic range. |  | EGAXT3 Triaxial Accelerometer
The Model EGAXT3 miniature triaxial accelerometers combine a damping ratio of 0.7 (Nominal) with built-in overrange stops that are set to protect the unit against 10,000g shocks. Available in ranges from ±5g to ±2500g. |  | EGCS-A2 & EGCS-B2 Accelerometers
The Model EGCS accelerometers combine a damping ratio of 0.7 (Nominal) with built-in overrange stops that are set to protect the unit against 10,000g shocks. Available in ranges from ±5g to ±5000g. |  | EGCS-D0 Accelerometer
The Model EGCS accelerometers combine a damping ratio of 0.7 (Nominal) with built-in overange stops that are set to protect the unit against 10,000 g shocks. It is a screw mount, stainless steel device. Available in ranges from ±5g to ±5000g. |  | EGCS-D1S Accelerometer
The Model EGCS accelerometers combine a damping ratio of 0.7 (Nominal) with built-in overange stops that are set to protect the unit against 10,000 g shocks. It is a screw mount, stainless steel device. Available in ranges from ±5g to ±5000g. |  | EGCS-L High Amplitude Shock Accelerometer
The Model EGHS-L is a high amplitude piezoresistive shock accelerometer designed for transient shock testing. Available in ±30,000g and ±60,000g ranges, it is packaged in a rugged welded stainless steel housing. |  | EGCS-S425 Accelerometer
The Model EGCS-S425 is a small, ISO 6487 and SAE J211 compliant piezoresistive accelerometer. Available in ranges from ±50g to ±2000g. |  | EGCS3-D Triaxial Accelerometer
The Model EGCS3-D triaxial accelerometer is available in ranges from ±5g through ±5000g. This rugged device is ideal for offshore, downhole and shock testing applications. |  | EGPE-1A IEPE Accelerometer
The model EGPE-1A is a high performance IEPE type accelerometer with an operating temperature range up to +150°C. It is available in ±10g to ±500g ranges and provides a flat frequency response up to 15kHz. |  | EGPE-2A Charge Accelerometer
The model EGPE-2A is a piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. It provides stable thermal response up to +260°C, and features the popular through hole mount installation. Available in ±50g to ±2000g dynamic range. |  | MiniSense 100 Accelerometer
The MiniSense 100 is a low cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. The sensor has excellent linearity and dynamic range, and may be used for detecting either continuous vibration or impacts. | | Accelerometers - Angular Accelerometers |  |  | ASB Angular Accelerometer
The JEWELL ASB Series Angular Accelerometer is a general purpose devise made for industrial, commercial, and aerospace sensing requirements. Its many applications include antennae stabilization, torque measurement, flight control systems, automotive testing, and optical system stabilization. | | Accelerometers - Board Level / OEM | |  | 832 Triaxial Accelerometer
The Model 832 is a low cost, board mountable triaxial accelerometer. It is hermetically sealed and incorporates full power and signal conditioning with a maximum current consumption of 4 micro-amps. Available in ±100g to ±500g ranges. |  | 832M1 Triaxial Accelerometer
The Model 832 is a low cost, board mountable triaxial accelerometer. It is hermetically sealed and incorporates full power and signal conditioning with a maximum current consumption of 22 micro-amps. Available in ±100g to ±500g ranges. |  | 834 High Amplitude Shock Accelerometer
The Model 834 is a low cost, board mountable triaxial accelerometer designed for high amplitude embedded shock applications. It is hermetically sealed and features a maximum current consumption of 4 micro-amps. Available in ±2000g to ±6000g ranges. |  | 834M1 High Amplitude Shock Acclerometer
The Model 834 is a low cost, board mountable triaxial accelerometer designed for high amplitude embedded shock applications. It is hermetically sealed and features a maximum current consumption of 22 micro-amps. Available in ±2000g to ±6000g ranges. |  | ACH-01 Accelerometer
The ACH-01 is a low cost, robust, general purpose accelerometer with outstanding performance characteristics. It is specifically designed for high volume applications that require the permanent installation of an accelerometer. | | MiniSense 100 Accelerometer
The MiniSense 100 is a low cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. The sensor has excellent linearity and dynamic range, and may be used for detecting either continuous vibration or impacts. |
 | 1600 Gold Standard™ Calibration Load Cell
For calibrating other load cells where best possible load cell is required. 4% lower load limit per ASTM E74. Provides tension & compression in 1 unit with <0.005% nonrepeatability. |  | 1601 Gold Standard™ Calibration Compression-Only Load Cell
The 1601 Gold Standard load cell is designed for calibrating other load cells where the best possible load cell is required. It has a 4% lower load limit per ASTM E74 and is a step above the 1100. The 1601 provides compression-only. |  | 1606 Gold Standard™ Low Capacity Calibration Load Cell
The 1606 Gold Standard load cell is designed for calibrating other load cells where the best possible load cell is required. It has a 4% lower load limit per ASTM E74 and is a step above the 1100. The 1606 is especially made for low capacity applications with capacities from 50 lbf. to 300 lbf. |  | 1800 Platinum Standard™ Calibration Load Cell
The 1800 Platinum Standard is the ultimate in calibration grade load cells and has a 2% lower limit per ASTM E74 and an integral stud. |  | BN100A Bridge Calibration Unit
The BN100A bridge calibration unit is a highly precise calibrator to calibrate measuring equipment and measurement chains which function with a carrier frequency of 225Hz. The BN100A bridge calibration unit is inserted in the measuring system to be calibrated in place of the transducer (full bridge), or is connected directly with the measuring instrument, and simulates with the aid of switchable inductive dividers the output signals of the transducer in a range of ±100mV/V. |  | Gold Standard™ Load Frames
Available in capacities 3K, 10K, and 55K. |  | K148 Calibration Unit for full bridge amplifiers
The K148 calibration unit simulates strain-gauge full bridges for amplifiers with one up to eight channels. The K148 comes with five measuring ranges with ten steps each. It enables DC and carrier frequency amplifiers from 225 Hz up to 4.8 kHz with measuring ranges from ±0.2 mV/V up to ±100 mV/V to be calibrated. |  | K3607 Calibration Unit
The K3607 calibration unit can be used to calibrate measuring amplifiers or measurement chains without imposing a mechanical quantity on the strain gauge transducers belonging to the measurement chain. For this purpose the calibration instrument is equipped with a high-precision resistance network in star configuration, designed to simulate 350-ohm strain gauge full-bridge transducers. |  | K800 Calibration Unit for 8-channel quarter-bridge amplifiers
The K800 calibration unit for strain gauge quarter bridges launched by HBM can calibrate eight channels simultaneously. The device is particularly useful for multi-channel measuring amplifiers, such as HBM’s MGCplus, that must be calibrated regularly to ensure accuracy. |  | TransCal 445 Portable
The Beran 445 Portable TransCal™ provides a simple-to-use, self-contained, battery powered calibrator. It consists of the drive generator, power amplifier, built-in shaker and reference accelerometer, all fitted into a rugged carrying case. |  | TransCal 455 Integrated Calibration System
The Beran 455 Integrated
TransCal™ provides, in one box, all of the measuring devices required to calibrate the majority of vibration transducers. The unit includes a power amplifier to provide drive to the user's shaker and two channels of matched signal conditioning amplifiers, one for the reference transducer and the other for the test transducer. |  | TransCal 475 Laboratory Calibration System
The Beran 475 Laboratory
TransCal™ is a dedicated, high precision instrument for the fully automatic calibration of vibration transducers. The sine correlation measurement technique is used in the Beran 475 to ensure that accurate, repeatable measurements are provided over a wide frequency range and with changing measurement environments. |
| Data Acquisition - Genesis HighSpeed - Power and Isolation products | |  | BE3200 Test Sequencer
The BE3200 test sequencer is designed for timing and sequence control of switchgear or ballistics tests. It replaces traditional electromechanical systems with microprocessor precision. Up to 32 optically-isolated outputs are available, with extensive interlocking and safety features. Windows software provides control in milliseconds, cycles or degrees of phase via an optically-isolated serial port. |  | ISOBE5600 Isolated Probe System
The ISOBE5600 is a fiber optic isolated probe system designed for remote measurements in high or low voltage environments, for current shunt measurements or just to provide safe isolation. With a DC to 20MHz bandwidth and carefully shielded transmitter, the Isobe5600 is versatile enough to be used for many applications in motor controls, power distribution, power supply testing, high voltage/high current, ballistics, ordnance and physiology. |  | MV-HV 6600 Isolated Digitizer
The 6600 Isolated Digitizer from HBM is a remote, fiber optic front end for the Genesis HighSpeed (GEN5i, GEN7t/14t) transient recorder. Each channel is completely remote programmable. The 6600 Isolated Digitizer is designed to be used in the harshest environments including the strongest electric and magnetic fields. The fiber optic link eliminates ground loops and guarantees a safe isolation between the device under test and the control room in short circuit, high voltage, and high power labs. | | Data Acquisition - High Speed - Dimension | |  | Dimension4i High Speed DAQ & Transient Recorder
Can be used both as a data recorder and a transient recorder. Combines all essential instruments in one device. Easy to understand and operate. |  | Accelerometer Digitizer
The Accelerometer Digitizer is a very versatile and high performing amplifier, ideal for powering ICP transducers, or accommodating AC and DC signals. This module is outfitted with state of the art components including 24-bit analog to digital converters (one per channel), dual 32 bit floating point digital signal processors, analog anti-aliasing filters. |  | Data Recorder Dimension4i (specifications)
Dimension4i can be used both as a data recorder and as a transient recorder – meeting the highest of demands. Dimension4i therefore combines all essential instruments in one device. Because Dimension4i was developed in cooperation with users as a professional tool for daily use, operation of the Dimension4i is intuitive and oriented towards the requirements of use: easy to understand, easy to operate. Routine tasks are quickly completed with Dimension4i so that you can concentrate fully on your tasks as a professional. |  | Isolated Digitizer
The Dimension Isolated Digitizer was designed for the extreme testing conditions and accuracy requirements of high voltage measurement applications. This module is outfitted with state of the art components including 24-bit analog to digital converters (one per channel), dual 32 bit floating point digital signal processors, isolation circuitry and analog anti-aliasing filters. | | Data Acquisition - High Speed - Genesis | |  | GEN7t & GEN16t High Speed - High Channel Count DAQ
With GEN7t/16t, you can configure up to 1,080 synchronized channels according to your requirements. Your system grows from the first channel onwards exactly as your project changes. Stay on top, rapidly, reliably, flexibly and always with perfect precision. Up to 8 GEN "slaves" can be connected to a GEN7t/16t master, each of these 9 devices can contain between 4 and 120 channels, and all 1,080 channels can measure in synchronization with each other. |  | GEN7t & GEN16t - mainframes & option
The GEN series Data Acquisition System is one of the most sophisticated and powerful systems in the marketplace and demonstrates the quality HBM has to offer. |  | Basic 1M Digitizer
8 Channel, 1MS/s, Basic Card, 256MB RAM (16 MS/ch) |  | Basic 1M ISO Digitizer
8 Channel, 1MS/s, Basic Card, 512MB RAM (32 MS/ch) - isolated, unbalanced-diff |  | Basic 1M XT ISO Digitizer
8 Channel, 1MS/s, Basic XT Card, 512MB RAM (32 MS/ch) - isolated, with extended input range |  | Basic 200K Digitizer
8 Channel, 200kS/s, Basic Card, 128MB RAM (8 MS/ch) | | BE3200 Test Sequencer
The BE3200 test sequencer is designed for timing and sequence control of switchgear or ballistics tests. It replaces traditional electromechanical systems with microprocessor precision. Up to 32 optically-isolated outputs are available, with extensive interlocking and safety features. Windows software provides control in milliseconds, cycles or degrees of phase via an optically-isolated serial port. |  | Binary Marker CT
The Binary Marker CT board CT is a dedicated binary input option for GEN DAQ products. It enables to record up to 64 binary input channels (marker channels) with up to 1 MS/s per channel. In addition 9 binary input channels can be assigned under software control to provide 3 channels of counter/timer functionality. Each channel can have its own function. |  | Binary Marker HV ISO
The Binary Marker HV board is a dedicated input option for GEN DAQ products. It enables to record up to 32 binary input channels (marker channels) as well as 8 digital event signals that are optically isolated with up to 1 MS/s per channel. |  | Bridge 1M ISO Digitizer
4 Channel, 1MS/s Bridge Card, 512MB RAM (64 MS/ch) - isolated |  | Bridge 200K ISO Digitizer
4 Channel, 200kS/s Bridge Card, 128MB RAM (16 MS/ch) - isolated |  | Fast Differential Digitizers
For ultra fast signals, the 25 MS/s and 100 MS/s high speed digitizer boards are equipped with four channels sampling at incredible high speed. With selectable anti-aliasing filtering and 14-bit (100 MS/s) or 15-bit resolution (25 MS/s), these inputs turn the GEN series into an extremely fast transient recorder. |  | GEN2i High Speed - Portable Data Recorder
GEN2i is a revolutionary new portable data recorder, offering incomparably powerful features and an exciting touchscreen user interface. With up to 16 input channels, fully configurable to your needs, it provides both continuous direct-to-disk as well as fast transient recording. |  | Genesis GEN5i Portable High Speed DAQ
The complete, portable test laboratory. Up to 40 channels available simultaneously. With integrated PC, you can measure directly at the event location & analyze the results. | | MV-HV 6600 Isolated Digitizer
The 6600 Isolated Digitizer from HBM is a remote, fiber optic front end for the Genesis HighSpeed (GEN5i, GEN7t/14t) transient recorder. Each channel is completely remote programmable. The 6600 Isolated Digitizer is designed to be used in the harshest environments including the strongest electric and magnetic fields. The fiber optic link eliminates ground loops and guarantees a safe isolation between the device under test and the control room in short circuit, high voltage, and high power labs. |  | Universal 1M ISO Digitizer
4 Channel, 1MS/s Universal Card, 512MB RAM (64 MS/ch) - isolated |  | Universal 200K ISO Digitizer
4 Channel, 200kS/s Universal Card, 128MB RAM (16 MS/ch) - isolated | | Data Acquisition - Laboratory Universal Data Acquisition | |  | MGCplus Data Acquisition System (overview)
With more than 100,000 channels in different applications worldwide, HBM's MGCplus system has achieved acceptance as a measurement standard. Supports a wide spectrum of transducers, fieldbus connections and standard PC interfaces. It is the choice for almost all industrial, laboratory and R&D measurement applications. Capable to measure force, displacement, pressure, temperature, torque, acceleration, strain, stress, voltage, current, frequency or resistance - at low or high speeds. |  | APxx Connection Boards for MGCplus
Connection boards for single channel or multi-channel amplifiers. Also connection boards for special-function modules. |  | Cpxx Communication Processors for MGCplus
Outstanding performance and use of standard PC interfaces distinguish the communication processors CP22 and CP42 for MGCplus. Both allow the assembly of networks: An important condition if data acquisition systems with more than 1,000 active channels should assembled. |  | ML38 High-precision Single-channel Amplifier Module for MGCplus
The ML38B precision amplifier provides a high resolution of 1,000,000, an accuracy of 0.0025% and an excellent long-term stability. |  | MLxx Amplifier & Communication Modules for MGCplus
Single-channel and multi-channel amplifer modules, and special-function modules for the MGCplus system. |  | CANHEAD Distributed Amplifier System
Simplify your measurement processes with CANHEAD® - and at the same time gain flexibility and efficiency. CANHEAD® is ideal for average to high channel counts. The 10-channel CANHEAD® amplifier modules can be installed in immediate proximity to the measuring points. Inexpensive and reliable standard fieldbus cables connect the CANHEAD® modules to a communication master. |  | CANHEADdirect Communication Module
The CANHEADdirect communication module enables measurement data of up to five CANHEAD® modules to be directly transmitted to a PC via CANbus. At a price that makes the CANHEAD® system the first choice for small and medium-sized applications in experimental structural and stress analysis as well. | | Data Acquisition - Rugged/Mobile - eDAQ | |  | eDAQ-lite Rugged Mobile DAQ
The eDAQlite is the go anywhere, test anything compact version of the SoMat eDAQ. Engineered using the same technology, the eDAQlite has similar leading-edge signal conditioning and a capacity to perform a broad range of on-board data processing, triggering, intelligent data storage, and complex computations. There is no learning curve, new software, or file formats; and systems can be seamlessly networked together. |  | EBRG eDAQ Bridge Layer
The SoMat eDAQ Bridge Layer (EBRG) offers 16 simultaneously sampled low level differential analog inputs through independent connectors. An extremely versatile layer; the Bridge Board works with both amplified and unamplified transducers including: strain gauges, accelerometers, pressure transducers, load cells, and other general analog signals. |  | ECOM eDAQ Vehicle Network Communications Layer
The SoMat eDAQ Vehicle Network Communications Layer (ECOM) offers (3) CAN device interfaces, (1) Vehicle Bus Module (VBM) interface and a GPS communications port. It is an extremely versatile layer providing a direct correlation between vehicle bus channels with physical data (analog, thermocouple and frequency) as well as GPS. |  | ECPU-PLUS Main Processor for eDAQ
For the system that defines Rugged, Mobile Data Acquisition, it all starts here. The SoMat eDAQ Base Processor (ECPU-PLUS) is the foundation eDAQ systems are built from. Specifically designed for these applications; input power for the system operates in a wide range from 10-60 VDC. Internal back-up batteries also protect the eDAQ from unplanned power losses or low voltage events. |  | EDIO eDAQ Digital Input-Output Layer
The SoMat eDAQ Digital Input/Output Layer (EDIO) is an extremely versatile layer that can measure digital inputs/outputs, pulse counters, quadrature decoders, vehicle bus, as well as GPS. The EDIO offers twenty four channels that can be used as digital inputs/outputs with twelve additional channels for wide range inputs. |  | EHLS eDAQ Simultaneous High Level Layer
The SoMat eDAQ Simultaneous High Level Layer (EHLS) offers 16 simultaneously sampled high-level differential analog inputs through independent connectors. Up to four EHLS layers can be added to a single eDAQ system enabling up to 64-channels. Networking multiple eDAQ’s make synchronous EHLS channel counts virtually limitless. |  | EITB eDAQ Isolated Thermocouple Layer
The SoMat eDAQ Isolated Thermocouple Layer (EITB) measures temperatures on 8-channels of isolated thermocouple signal conditioning. Thermocouples come in several styles of dissimilar metals, or calibrations; and the EITB is available in the four most common calibration types (J, K, T and E). Each channel has individual cold junction compensation with isolation to 500V. |  | ENTB eDAQ Non-Isolated Thermocouple Layer
The SoMat eDAQ Non-Isolated Thermocouple Layer (ENTB) measures temperatures on 32-channels of non-isolated thermocouple signal conditioning. Thermocouples come in several styles of dissimilar metals, or calibrations; and the ELNTB is compatible with the four most common calibration types (J, K, T and E). Each channel is individually software-selectable between these calibrations. |  | eDAQ Rugged Mobile DAQ
Sets the standard for rugged, mobile data acquisition; a stand-alone sealed system designed for testing in the harshest of environments. |  | ELBAT-2 eDAQ-lite Battery Layer
The SoMat eDAQ-lite Battery Layer (ELBAT-2) is located below the eDAQ-lite in a machined aluminum enclosure. It attaches with four 8-32 screws to the base plate of the eDAQ-lite replacing the rubber feet. The feet can be relocated to the battery layer for mounting purposes. A short cable, with the eDAQ D-Sub power connector, connects to the eDAQ-lite and is also utilized for charging purposes. |  | ELBRG eDAQ-lite Bridge Layer
The SoMat eDAQ-lite Bridge Layer (ELBRG) offers four simultaneously sampled low level differential analog inputs through independent connectors. An extremely versatile layer; the Bridge Board works with both amplified and unamplified transducers including: strain gauges, accelerometers, pressure transducers, load cells, and other general analog signals. |  | ELCPU eDAQ-lite Base Processor
The SoMat eDAQ-lite Base Processor (ELCPU) is the foundation eDAQ-lite systems are built from. Specifically designed for rugged, mobile applications; input power for the system operates in a wide range from 10-60 VDC (with ELCPU-PLUS option). Internal back-up batteries also protect the eDAQ-lite from unplanned power losses or low voltage events. |  | ELDIO eDAQ-lite Digital Input-Output Layer
The SoMat eDAQ-lite Digital Input/Output Layer (ELDIO) is an extremely versatile layer that can measure digital inputs/outputs, pulse counters, quadrature decoders, vehicle bus, as well as GPS. The ELDIO offers eight channels that can be used as digital inputs/outputs with four additional channels for wide range inputs. |  | ELHLS eDAQ-lite Simultaneous High Level Layer
The SoMat eDAQ-lite Simultaneous High Level Layer (ELHLS) offers 4 simultaneously sampled high-level differential analog inputs through independent connectors. Up to eight ELHLS layers can be added to a single eDAQ-lite system enabling up to 32 channels. Networking multiple eDAQ’s make synchronous ELHLS channel counts virtually limitless. |  | ELNTB eDAQ-lite Non-Isolated Thermocouple Layer
The SoMat eDAQ-lite Non-Isolated Thermocouple Layer (ELNTB) measures temperatures on 16-channels of non-isolated thermocouple signal conditioning. Thermocouples come in several styles of dissimilar metals, or calibrations; and the ELNTB is compatible with the four most common calibration types (J, K, T and E). | | Data Acquisition - Rugged/Mobile - Liberty | |  | Liberty Rugged Portable High Speed DAQ
Product tests in vehicle construction and aerospace, or the commissioning and servicing of industrial infrastructures, do not take place under air-conditioned laboratory conditions. Instead, conditions usually include vibrations and shocks, spray water, dirt and extreme external temperatures. You can now gain the freedom to carry out measurements anywhere, even under these rough conditions with the Liberty system. |  | Liberty Rugged Portable High Speed DAQ (data sheet)
Product tests in vehicle construction and aerospace, or the commissioning and servicing of industrial infrastructures, do not take place under air-conditioned laboratory conditions. Instead, conditions usually include vibrations and shocks, spray water, dirt and extreme external temperatures. You can now gain the freedom to carry out measurements anywhere, even under these rough conditions with the Liberty system. |  | Accelerometer Digitizer
Each module contains a 16-bit digitizer on each channel with 100mV-40V full scale ranges, 8-pole Butterworth 20kHz Anti-alias filter, and selectable Bessel or Butterworth FIR digital filter. Integrated programmable excitation of 1 mA to 15 mA @ 28 V nominal. |  | Bridge Plus Digitizer
Each module contains a 16-bit digitizer on each channel with 2mV-10V full scale ranges, 6-pole Butterworth 20kHz Anti-alias filter, and a selectable Bessel or Butterworth FIR digital filter. Integrated excitation is 0 to 10V bipolar, 30mA. Includes bipolar shunt and monitor output. |  | CANbus Digital Input Card
Each module has one or two CAN nodes plus 32 digital inputs including counter/timer, frequency, RPM and quadrature encoder channels. |  | DC-32 and TC Digitizer
The DC-32 module contains a 10kS/s, 16-bit digitizer on each of 32 channels with 1V to 5V ranges F.S. |  | General Purpose Digitizer
Each module contains a 100kS/s, 16-bit digitizer on each channel with 100mV-40V full scale ranges, 8-pole Butterworth 20kHz Anti-alias filter, and selectable Bessel or Butterworth FIR digital filter. | | Data Acquisition - Universal Data Acquisition | |  | QuantumX (overview)
QuantumX is a universal data acquisition system. "Universal" means that QuantumX can be used with all types of transducers. Its universal flexibility also means that you can use it to conduct all kinds of test and measurement tasks as well as for verification of results in any type of industrial environment. |  | QuantumX CX27 Ethernet-EtherCAT Gateway
CX27 allows integration of several QuantumX modules for real-time data acquisition of up to 199 signals via EtherCAT. Selected signals can simultaneously be monitored via Ethernet TCP/IP. |  | QuantumX MX1609 16-channel Thermocouple Amplifier
MX1609 is part of the QuantumX family and offers many excellent qualities: Reliable temperature measurement using the proven and widely used type K thermocouple – at the same time opening up fascinating new opportunities for your day-to-day measurement tasks. |  | QuantumX MX410 4-channel High-Dynamic Universal Amplifier
The MX410 provides both sampling rates of up to 96 kHz/channel and a high resolution of 24 bits. Results are highly accurate as required when capturing highly dynamic forces and accelerations. Compatible with strain gage transducers in half and full bridge configuration (DC, 4.89 kHz CF) as well as with inductive half and full bridges and current-fed piezoelectric sensors (IEPE). |  | QuantumX MX440A 4-channel Universal Amplifier
4 individually adjustable inputs, 24-bit A/D converter per channel, sampling rate of up to 19.2 kHz/channel (adjustable). Small; fits into any test bench. |  | QuantumX MX460 4-channel Frequency Measuring Amplifier
Capture digital rotational speed signals or evaluate pulse width modulation signals (PWM). Or integrate the worldwide leading HBM torque transducers into the QuantumX universal data acquisition system. Features sampling rates of up to 96 kHz/channel and a bandwidth of up to 38 kHz. An ideal choice for applications in motor and drivetrain development. |  | QuantumX MX840A 8-channel Universal Amplifier
8 individually adjustable inputs, 24-bit A/D converter per channel, sampling rate of up to 19.2 kHz/channel (adjustable). Small; fits into any test bench. |  | QuantumX MX878 Transmitter with 8 analog voltage outputs
The MX878 transmitter enables scaled measurement signals to be monitored in a standardized unit of measurement or transmitted to other systems to allow flexible and efficient data analysis. In addition, signals can be set off against each other using algebraic operations. The module also features functions for peak value analysis. |  | Spider8 Multi-Channel Electronic PC Measurement Unit
Spider8 is a multi-channel electronic PC measurement unit for parallel, dynamic measurement data acquisition using a computer. The Spider8 offers a congenial and economic alternative to systems consisting of a number of components. These are usually accommodated partly in the computer and partly externally and must first be wired and configured to form a measurement system. |
 | 9320 Hand Held Digital Indicator
The 9320 is a bipolar 7-digit hand held meter featuring two independently scalable ranges, peak and valley monitoring, display hold, mV/V calibration and a power save feature. Typical battery life exceeds 40 hours of continuous use. IEEE1451.4 TEDS Plug & Play compliant. |  | 9820 Digital Indicator
Bipolar, 5-digit display featuring 2000Hz high-bandwidth, +/-10V analog output, front-panel shunt calibration and tare, peak and valley monitoring. Sensor connection is via a removable screw-terminal connector. |  | 9830 Digital Indicator
Bipolar 5-digit display with 120 sample/second internal update rate, 2000Hz high bandwidth +/-10v and 4-20mA outputs, front panel shunt calibration and tare, RS232 and digital output setpoints and adjustable digital filter. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector. |  | 9834 Digital Indicator
For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector. |  | 9840 Intelligent Digital Indicator
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance. |  | 9850 Multi-Channel Digital Indicator
The model 9850's modular design allows the use of 7 different types of channel cards in 2 available channels. Available channels include AC mV/V for use with Rotary Transformer type torque sensors, DC mV/V, +/-5V or +/-10V, 4-20mA, Frequency (speed), Encoder and LVDT position sensors. A 3rd math channel allows display of calculate values such as horsepower, unit conversion, peak or valley, etc. The dual +/-10V analog outputs are assignable to any of the three channels. 2000 Hz sample rate allows true peak monitoring. Included software for graphical data display and logging. |  | 9860 Digital Indicator
Similar to the 9830 indicator, but with TEDS functionality. |  | DML300 Single Channel LVDT Panel Indicator
The DML300 series of digital panel indicators is designed specifically for use with LVDT transducers. DML300 series indicators have a five digit display, transducer excitation supply and many software features including max/min memory and math functions. All models are fitted with two analogue outputs - a high speed analogue output for monitoring fast changes of sensor movement, and a separate, electrically isolated, scaleable analogue output. |  | DMP200 Single Channel Digital Panel Indicator
The DMP200 can be used for both simple ´measurement only´ applications and in more demanding situations requiring digital communications, alarms, maths functions and complex signal conditioning. Ideally suited to operate with Penny & Giles linear and rotary potentiometers, providing a 10 Vdc or 0-12 Vdc transducer supply. This model is also suited to operate with thermocouples and RTDs, as well as pressure transducers, load cells and strain gauges. |  | MP2000 Digital Indicator
This microprocessor based LVDT indicator and set-point controller is designed for industrial and process control applications utilizing any LVDT/RVDT-based measurement device. In addition to displaying real-time readings of LVDTs, RVDTs and gage heads, the MP2000 also displays MIN, MAX, TIR, A+B and A-B values. |  | MVD2510 Panel Meter Amplifier
Control panel measuring amplifier for process control and test bencher. |  | MVD2555 Panel Meter Amplifier
Carrier frequency amplifier for panel mounting. |  | PML-1000 Panel Meter
The PML1000 is an AC line powered LVDT/RVDT panel meter that is ideal for industrial and test applications. For control applications, it has a fast (125 Hz) unscaled analog output, an isolated 0-10 VDC/4-20 mA scaleable output and optional serial 2 or 4 wire RS 422/485 communications. |  | Scout55 4.8kHz Carrier-Frequency Amplifier
The SCOUT55 measuring amplifier is suitable for recording and processing measured values from passive transducers. Transducers that can be connected are: strain-gauge half and full bridges, inductive half and full bridges, LVDTs, piezoresistive transducers, potentiometers. |  | THPS-100 Single Channel PowerPod
The THPS-100 is a self-contained power supply and display designed for gas mass flow-meters. It features an automatically generated set point (0-5V or 0-10V) and RS232 communication. |  | THPS-400 Four Channel PowerPod
The THPS-400 is a power supply and indicator capable of displaying four channels simultaneously. It has an integrated totalizer, filter function, and Serial communication. Has the ability to set ratio control for gas blending applications. |
| Encoders - Magnetic Encoders | |  | ED-18 Magnetic Encoder
The ED-18 Series magnetic encoder can be used as either a rotational feedback sensor or as a human machine interface (HMI) device. As a light duty feedback sensor it can provide rotation speed, direction or positioning information. The analog output provides absolute angular position information even when power is cycled on and off. As an HMI device it can be used as a rotary input control for use on instrumentation panels. |  | ED-19 Magnetic Encoder
The ED-19 Series magnetic encoder is designed for medium duty feedback applications. Resolutions are available from 64 to 1024 counts per revolution. The magnetic technology used in the ED-19 series is plug-in compatible with existing encoder products, with the added advantages of an extended temperature range and fully sealed electronics. The ED-19 suffers no LED degradation, meaning it has a virtually unlimited life. |  | ED-20 Magnetic Encoder
The ED-20 Series magnetic encoder is designed for medium duty industrial feedback applications with ball bearing supported shaft. Resolutions are available from 200 to 1024 counts per revolution. This encoder series also features line drivers with active termination for long cable runs and reverse voltage protection. The ED-20 also offers the option of high voltage differential, low voltage differential or open collector (NPN) outputs. |  | ED-21 Magnetic Encoder
The ED-21 Series magnetic encoder is designed to replace traditional mechanical potentiometers. This product is offered with a ball bearing supported shaft. Five standard output ranges are available: 0.5 - 4.5v, 0 - 5v, 0 - 12v, 4 - 20mA and 0 - 20mA. The magnetic technology used in the ED-21 offers advantages over conventional electromechanical potentiometers with sealed electronics, extended temperature ranges, and virtually unlimited life. |  | ED-22 Magnetic Encoder
The ED-22 Series magnetic potentiometer can be used to replace a conventional potentiometer. This product offers 270 degrees of electrical travel, integrated rotational stop system, 300 degrees of mechanical travel, utilizing a sleeve bearing and shaft fitted with an O-ring seal. The non-contact magnetic sensor design utilized in the ED-22 is well suited for industrial applications with temperature extremes, high vibration and shock, and contamination. |
| Fluid Properties Sensors - Fluid Property Analyzers | |  | FPA4200BST Fluid Property Analyzer
The fluid property analyzer (FPA) is designed to provide customers with an industrial robust and flexible platform for monitoring applications that may include distillation and chemical process streams, machinery lubricants, and gear oils. |
 | Humidity Sensors (overview)
Humidity sensors can improve performance, reduce energy consumption and increase safety in a variety of applications. Increasingly, OEMs are designing relative humidity/temperature sensors into engines, electronics, and other products to improve control and output. |
 | JC2000 Multi-Axis Contactless Joystick
The JC2000 is designed for precision fingertip control applications where safety and long trouble-free life are primary requirements. Available in one, two or three axis configurations and can accommodate a choice of handles, including push-button switch versions. |
| Linear Position Sensors - Capacitive | |  | MicroSense 4810
The ADE model 4810 is a non-contact precision position sensor. The 4810 is optimized for short range displacement measurement applications that require best possible linearity and stability.
|  | Microsense 5000 Series Probes
Many sensor heads, or probes, are available for use with our 5800 Series capacitive position sensors. |  | Microsense 5810
The ADE Model 5810 is a single channel, non-contact precision capacitive displacement sensor. Designed for high dynamic applications, the Model 5810 provides high resolution with measurement bandwidth up to 100 kHz |  | Microsense 8810
The ADE model 8810 is a non-contact precision position sensor. The 8810 is designed for best linearity and stability, with measurement bandwidth up to 20 kHz – ideal for servo system position feedback and fast tool servo applications |  | Microsense Mini
The MicroSense Mini is a compact, high resolution linear displacement sensor designed specifically for providing servo system feedback, especially for OEM applications. |  | Precision Capacitive Sensor Model 6810
Break the nanometer resolution barrier -- achieve picometer resolution with our highest resolution position sensor - ADE Technologies introduces our new Model 6810 high resolution capacitive position sensor. | | Linear Position Sensors - Hall Effect | |  | SLH100 Hall Effect Contactless Linear Sensor
Designed to provide precision cost effective position sensing using the proven contactless Hall effect principle. The sensing system has two parts; sensor and magnetic activator. | | Linear Position Sensors - In-Cylinder | |  | ICT080 Contactless In-Cylinder Linear Transducer
With a body diameter of only 8mm the ICT080 is ideal for installation into hydraulic and pnematic cylinder applications where space is at a premium. With no electrical sliding contacts, the ICT080 has a working life which is almost limitless. |  | ICT100 Contactless In-Cylinder Linear Transducer
With a body diameter of only 10.1mm the ICT100 is ideal for installation into hydraulic and pnematic cylinder applications where space is at a premium. With no electrical sliding contacts, the ICT100 has a working life which is almost limitless. | | Linear Position Sensors - Inductive | |  | SLT190 Contactless Linear Position Transducer
Designed to provide reliable, fit-and-forget position sensing (up to 500mm) within a compact transducer size for the most arduous operating environments. |  | W1ELA Inductive Displacement Transducer
The type W1ELA/0-2 inductive displacement sensors are normally installed, for example in machines, test equipment and measuring instruments. The sensors are available with an accuracy class of 0.2 for 4.8 kHz carrier frequency. |  | WA Inductive Displacement Transducer
The WA is a rugged series of inductive displacement transducers that combine very good linearity with excellent thermal behaviour in the shortest possible overall length. Available in plunger or probe versions. |  | WI Miniature Probe
Th WI series miniature probes are available in nominal (rated) measuring lengths of 2 mm, 5 mm and 10 mm with 8 mm clamping. They comply with protection class IP67. | | Linear Position Sensors - LVDT | |  | AF111 LVDT Displacement Transducer
Suitable for clamp mounting, the AF111 has a threaded, unguided core assembly to simplify installation. The transducer coil has been specifically designed to reduce overall transducer length and to enable high accuracy. |  | AF145 LVDT Displacement Transducer
The AF145 features self-aligning rod end bearings for mounting. The transducer coil has been specifically designed to reduce overall transducer length and to enable high accuracy ratiometric operation. |  | DC-EC AccuSens LVDT
The DC–EC AccuSens™ Series incorporates a unique monolithic chip combined with a computer-designed AC LVDT to achieve premium performance. The ratiometric design of the monolithic circuitry compensates for power supply deviations for continuously stable operation. Unaffected by input variations, the transducer provides highly accurate, repeatable measurement. |  | DC-SE LVDT
The DC-SE series has been designed to meet today’s requirements for operation from a single-ended power supply. The output is also single-ended over the full range displacement of the LVDT making the unit compatible with unipolar inputs on analog-to-digital converters and programmable logic controllers, etc. |  | E LVDT
The E Series of LVDTs is economical and satisfies numerous applications where LVDT performance and reliability are desired, but where budgets are limited. Linearity is 0.5% of full-range for all units except the E2000. The E series is particularly suitable for moderate operating temperatures. |  | GC-485 Digisense Gauge Head
GC-485 DigiSense™ Gage Head is available in five bipolar measurement ranges, with standard strokes from ± .050 inches to ± 1.0 inch. The single ended 8.5 to 30.0 volt dc. input and two-wire, addressable RS-485 output, make the GC-485 ideally suited to factory automation applications. Direct digital output eliminates the need for expensive and error prone analog to digital conversion. |  | GCA Gauge Head
GCA Series gage head with stainless steel construction enables the performs in environments containing moisture, dirt and other contaminants. Electronic components are hermetically sealed for added protection against hostile conditions. These are heavy duty, long stroke units with ranges up to ±2.0" (50mm). Maximum spring force is typically 8 oz (226.8g), dependent upon probe position. |  | GCD Gauge Head
GCD Series gauge head with stainless steel construction enables the performs in environments containing moisture, dirt and other contaminants. Electronic components are hermetically sealed for added protection against hostile conditions. These are heavy duty, long stroke units with ranges up to ±2.0" (50mm). Maximum spring force is typically 8 oz (226.8g), dependent upon probe position. |  | GCD-SE Gauge Head
The GCD-SE Series is available in five uni-polar measurement ranges, with standard strokes from 0 to 0.1 inch to 0 to 2.0 inches. Operating on a single ended 8.5 to 28.0 volt dc. input, and minimal current draw, the GCD-SE is ideally suited to portable measurement applications. Hermetically sealed, the GCD-SE is also well suited to in-process wet grinding and machining applications. |  | HR LVDT
The HR Series of LVDTs is highly reliability and is suitable for most general applications. The HR Series features a large core-to-bore clearance, high output voltage over a broad range of excitation frequencies, and a magnetic stainless steel case for electromagnetic and electrostatic shielding. |  | LBB Ultra Precision Gauge Heads
The Linear Ball Bearing (LBB) Series of dimensional gaging probes is engineered for highly precise and repeatable measurements in quality control and metrology applications. LBB within the gaging probe minimize radial play and friction for ultra-precise measurement. |  | MHR Miniature LVDT
The MHR Series of LVDTs is ideal for applications where excessive core weight could influence the motion of sensitive mechanisms. The lightweight core also helps minimize stresses and preserves the structural integrity of the core actuation assembly. High sensitivity results from close electrical coupling between coil and core. A magnetic stainless steel housing provides electromagnetic and electrostatic shielding. |  | PCA-116 Economy Gauge Head
Our PCA-116 family of gage heads was developed for less demanding applications where a balance between cost and performance is paramount. PCA-116 gage heads incorporate a standardized LVDT with repeatability better than 0.0001" (0.0025 mm) and linearity within 0.5% of full range output. The probe shaft is externally sprung and is carried on low friction nylon sleeve bearings. |  | PCA-375 Gauge Head
The PCA-375 Series gage head is based on the MHR series of LVDTs. The modified MHR has an extended case and spring-loaded plunger. The design goals were simplicity and high reliability with low cost. |  | PCA-375 PR-020 Ultra Compact Gauge Head
The PCA-375 PR-020 Series gage head is an ultra-compact device that provides accurate measurement in areas with limited space. Designed with a radial cable exit, the gage head easily fits within miniature fixtures and small inside diameters. AC operated, this ultra-compact gage head is compatible with all Measurement Specialties signal conditioning. |  | XS-ZTR Nuclear Radiation Resistant LVDT
The XS-ZTR Series LVDT is designed for measuring displacement at very high and cryogenic temperatures. The XS-ZTR operates continuously at 550°C and will survive 650°C for several hours. The XSZTR is also designed to perform within specification after exposure to a total integrated flux of 1011 rads gamma or 3 x 1020 NVT. | | Linear Position Sensors - Potentiometers | |  | HLP190 Spring Loaded Linear Potentiometer
The HLP190 linear potentiometers has a body diameter of only 19mm with stroke lengths from 25mm to 150mm, and a choice of body clamp (BS) or flange (FS) mounting. This model is supplied with a spring loaded shaft, biased to the fully extended position. |  | SLS095 Linear Potentiometer
The SLS095 comes in an extremely compact, lightweight package in stroke lengths from 10 to 100mm. The miniature size of this new sensor makes it ideal for applications in robotics, animatronics, medical equipment and motorsport data acquisition. |  | SLS130 Linear Potentiometer
The SLS130 comes in an extremely compact, lightweight package in stroke lengths from 25 to 200mm. It is ideally suited to high volume OEM manufacturers, where high performance and reliability has paramount importance. |  | SLS190 Linear Potentiometer
The SLS190 is available in stroke lengths from 25 to 350mm. Using the proven benefits of Hybrid Track Technology, the SLS190 is ideally suited to high volume OEM manufacturers. |  | SLS220 Spring Loaded Linear Potentiometer
The SLS220 is available in stroke lengths of 10 and 20mm, with a spring loaded operating shaft. This unit has a mounting flange to allow easy installation. | | Linear Position Sensors - String (Draw Wire) Potentiometers | |  | DLS Draw Wire Linear Sensor
The DLS series of draw-wire linear position sensors are a cost effective way to measure linear displacements up to 5000mm in the most demanding industrial environments. |  | DP-series Digital Position Transducer
AMETEK RayelcoTM Digital Position Transducers (Optical Encoder Type) are designed to provide a digital output signal with an accuracy of 0.05% (+1 pulse) FS. The transducer operates from a variable voltage source of 4.75 Vdc to 30 Vdc @ 50 mA maximum. The three output channels "A", "B" & Index are TTL/CMOS compatible, single ended (Open Collector). The output signal current is +20 mA maximum, thereby eliminating line drivers for long electrical connections. |  | MP-series Miniature Position Transducer
AMETEK RayelcoTM Miniature Position Transducer has been designed to provide maximum user flexibility. This unit can be mounted in confined areas and by simply loosening a single bolt, direct the cable in any direction by turning the transducer body 360 degrees and the mounting swivel 180 degrees. Slotted cable entry allows the cable to be out of alignment by as much as ±10 degrees in one axis. Available in ranges up to 20 inches. |
| Load Cells / Force Transducers - Axial Torsion | |  | 1216 Axial Torsion Load Cell
The 1216 Axial-Torsion load cell measures both force and torsion in the same cell - with either channel capable of being used independently. Available in capacities from 250 lbf. to 2K lbf. |  | 1516 Axial Torsion Load Cell
The 1516 is a low profile load cell designed for applications where axial and torsion loads need too be measured simultaneously. Available in capacity 100 lbf./50 lbf-in. |  | 2816 Axial Torsion Load Cell
The 2816 Axial-Torsion load cell measures both force and torsion in the same cell - with either channel capable of being used independently. Similar to the 1216, but with a lower profile and capable of much higher forces and torques. Available in capacities of 3.3K lbf. to 15K lbf. | | Load Cells / Force Transducers - Beam Type | |  | MB Miniature Beam Load Cell
The MB is a miniature beam load cell used in medical test machine and a variety of low capacity applications. Available in capacities from 5 lbf. to 250 lbf. |  | MBI Fatigue Rated Mini Beam Overload Protected Load Cell
Similar to MBP mini beam but with better resistance to off center loads. Available in capacities from 2 lbf. to 10 lbf. |  | MBP Miniature Beam Overload Protected Load Cell
The MBP is the same as MB mini beam with internal overload protestion. It is a miniature beam load cell used in medical test machine and a variety of low capacity applications. Available in capacities from 2.5 lbf. to 10 lbf. |  | SSB Sealed Beam Load Cell
The SSB is a sealed version of MB mini beam. Available in capacities from 50 lbf. to 1K lbf. | | Load Cells / Force Transducers - Calibration Grade Low Profile Load Cells | | | 1600 Gold Standard™ Calibration Load Cell
For calibrating other load cells where best possible load cell is required. 4% lower load limit per ASTM E74. Provides tension & compression in 1 unit with <0.005% nonrepeatability. | | 1601 Gold Standard™ Calibration Compression-Only Load Cell
The 1601 Gold Standard load cell is designed for calibrating other load cells where the best possible load cell is required. It has a 4% lower load limit per ASTM E74 and is a step above the 1100. The 1601 provides compression-only. | | 1606 Gold Standard™ Low Capacity Calibration Load Cell
The 1606 Gold Standard load cell is designed for calibrating other load cells where the best possible load cell is required. It has a 4% lower load limit per ASTM E74 and is a step above the 1100. The 1606 is especially made for low capacity applications with capacities from 50 lbf. to 300 lbf. | | 1800 Platinum Standard™ Calibration Load Cell
The 1800 Platinum Standard is the ultimate in calibration grade load cells and has a 2% lower limit per ASTM E74 and an integral stud. | | Load Cells / Force Transducers - Column / Rod End | |  | 2100 High Capacity Column Load Cell
The 2100 is a column load cell typically used in higher force applications. Available in capacities from 300K lbf. to 1000K lbf. |  | 2120 Rod End
The 2120 rod end load cell is typically used with actuators where sensitivity to side loads is not important. |  | 2200 Calibration Column Load Cell
Many customers perform 100 and 200K E4 calibrations of material test machines in the field. Interface has developed the relatively lightweight portable 2200 series column load cells to use for field testing applications. These are very accurate column cells and come with handles to facilitate transportation from the vehicle to the job site. They also come standard with 16 gages as well as E74 calibration. | | Load Cells / Force Transducers - Dual Range | |  | 2101 Dual Range Standard Compression-Only Load Cell
The 2101 consist of lower and higher capacity model 1200 type load cells which are stacked with overload protection built into the lower capacity load cell permitting high resolution to be obtained at both low and high levels of capacity. | | Load Cells / Force Transducers - Load / Force Washers | |  | ELWF Load Washer
The ELWF is a compression load washer typically used in bolt loads, assembly forces, biomechanical force measurement, tool forces, thrust measurements, and robotics end effectors. Available in capacities from 5 lbf. to 2K lbf. | | Load Cells / Force Transducers - Load Buttons | |  | C2 Compression Force Transducer
The C2 force transducer is designed for compressive loading applications with a key feature being its low height. Ranges are available from 0.5kN to 200kN. |  | C9B Compression Force Transducer
The C9B force transducer is suitable for measuring static or dynamic compressive forces. The sensor is designed for applications where space is at a premium. Ranges are available from 50N to 50kN. |  | ELAF Compression Load Cell
The ELAF is a compression-only load cell, typically used in theatrical rigging loads, assembly forces, weighing, tool forces, thrust measurements, batch weighing, robotics end effectors, product validation testing, material test, and hoist and winch loads. Available in capacities from 10 lbf. to 5K lbf. |  | ELFF Load Cell
The ELFF is a compression or tension & compression load cell typically used in surface mount assembly system force feedback, robotics end effectors, weighing, dental and biomechanical parameter measurements, satellite and aerospace force feedback, and ultra low deflection applications. Available in capacities from 10 lbf. to 100 lbf. |  | ELHM Load Cell
The ELHM is a compression or tension & compression load cell, typically used in theatrical rigging loads, assembly forces, weighing, tool forces, thrust measurements, demanding longer term measurements, product validation testing, material test, and hoist and winch loads. Available in capacities from 500 lbf. to 10K lbf. |  | ELHS Load Cell
The ELHS is a compression or tension & compression load cell typically used for assembly forces, applications requiring ultra fast response, tool forces, thrust measurements, measurements requiring low sensor deflection and high resolution, and product validation testing. Available in capacities from 20 lbf. to 10K lbf. |  | LBM Compression Load Button
The LBM is a compression only load button designed for relatively small spaces. Available in capacities from 25 lbf. to 50K lbf. |  | LBS Miniature Compression Load Button
The LBS is a smaller less accurate version of the LBM. It is a compression only load button designed for very small spaces. Available in capacities from 5 lbf. to 1K lbf. | | Load Cells / Force Transducers - Low Capacity | |  | ULC Ultra Low Capacity Load Cell
The ULC is the world's most accurate ultra low capacity load cell measuring loads from 50 grams to 500 grams. | | Load Cells / Force Transducers - Low Profile Load Cells | |  | 1000 Fatigue Rated High Capacity Load Cell
The 1000 series is a fatigue rated load cell with 300% overload protection, an extremely low moment sensitivity of .1%/in, low zero float(toggle) and a higher fatigue life than competitive Stainless Steel load cells. Available in capacities from 100K lbf. to 1000K lbf. |  | 1000 Fatigue Rated Load Cell
The 1000 series is a fatigue rated load cell with 300% overload protection, an extremely low moment sensitivity of .1%/in, low zero float (toggle) and a higher fatigue life than competitive stainless steel load cells. Available in capacities from 250 lbf. to 50K lbf. |  | 1100 Ultra Precision Load Cell
The 1100 is selected from the best load cells and has very low nonlinearity, hysteresis, eccentric load sensitivity, and temperature sensitivity. Available in capacities from 300 lbf. to 200K lbf. |  | 1101 Ultra Precision Compression-Only Load Cell
The 1100 is selected from the best load cells and has very low nonlinearity, hysteresis, eccentric load sensitivity, and temperature sensitivity. Available in capacities of 1K lbf. to 50K lbf. |  | 1200 Standard 3-Wire Amplified Load Cell
The 1200 Low Profile is Interface's most popular load cell and is designed for static applications. With the electronics built into the load cell, there is no need for a separate signal conditioner. Available in capacities of 300 lbf. to 100K lbf. |  | 1200 Standard High Capacity Load Cell
The 1200 has higher output than most competitive load cells and is designed for general purpose applications requiring a load cell compensated for eccentric loads. Available in capacities from 200K lbf. to 2000K lbf. |  | 1200 Standard Load Cell
Higher output than most competitive load cells. For static, general purpose applications requiring a load cell compensated for eccentric loads. Comes in capacities of 300 lbf. to 100K lbf. |  | 1201 Standard Compression-Only Load Cell
The 1200 Low Profile is Interface's most popular load cell and is designed for static applications. The 1200 has higher output than most competitive load cells and is designed for general purpose applications requiring a load cell compensated for eccentric loads. Available in capacities of 1K lbf. to 400K lbf. |  | 1500 Standard Low Capacity Load Cell
The 1500 is a fatigued rated Low profile load cell is designed for low capacity applications where low sensitivity to eccentric load is important. Available in capacities from 50 lbf. to 300 lbf. |  | 2451-2461 Stainless Steel Compression-Only Load Cell
Interface has developed the new compact compression only 2451/2461 for applications requiring a very small footprint. The 2451 comes in 3 capacities, 50, 75, and 100K, each only 4.5” in diameter. The 2461 comes in 2 capacities, 150 and 200K, each only 5.5” in diameter. |  | 3420 & 3430 Coil Tubing Load Cells
The 3420 & 3430 load cells are designed for measuring tension and compression on coil tubing in the oil industry. Available in capacities from 20K lbf to 50K lbf. | | Load Cells / Force Transducers - Miniature | | | ELAF Compression Load Cell
The ELAF is a compression-only load cell, typically used in theatrical rigging loads, assembly forces, weighing, tool forces, thrust measurements, batch weighing, robotics end effectors, product validation testing, material test, and hoist and winch loads. Available in capacities from 10 lbf. to 5K lbf. | | ELFF Load Cell
The ELFF is a compression or tension & compression load cell typically used in surface mount assembly system force feedback, robotics end effectors, weighing, dental and biomechanical parameter measurements, satellite and aerospace force feedback, and ultra low deflection applications. Available in capacities from 10 lbf. to 100 lbf. | | ELHM Load Cell
The ELHM is a compression or tension & compression load cell, typically used in theatrical rigging loads, assembly forces, weighing, tool forces, thrust measurements, demanding longer term measurements, product validation testing, material test, and hoist and winch loads. Available in capacities from 500 lbf. to 10K lbf. | | ELHS Load Cell
The ELHS is a compression or tension & compression load cell typically used for assembly forces, applications requiring ultra fast response, tool forces, thrust measurements, measurements requiring low sensor deflection and high resolution, and product validation testing. Available in capacities from 20 lbf. to 10K lbf. |  | ELPF Load Cell
The ELPF is a compression or tension & compression load cell typically used for theatrical rigging loads, assembly forces, tool forces, thrust measurements, batch weighing, robotics end effectors, product validation testing, medical instruments, and hoist and winch loads. Available in capacities from 10 lbf. to 500 lbf. | | LBM Compression Load Button
The LBM is a compression only load button designed for relatively small spaces. Available in capacities from 25 lbf. to 50K lbf. | | LBS Miniature Compression Load Button
The LBS is a smaller less accurate version of the LBM. It is a compression only load button designed for very small spaces. Available in capacities from 5 lbf. to 1K lbf. | | MB Miniature Beam Load Cell
The MB is a miniature beam load cell used in medical test machine and a variety of low capacity applications. Available in capacities from 5 lbf. to 250 lbf. | | MBI Fatigue Rated Mini Beam Overload Protected Load Cell
Similar to MBP mini beam but with better resistance to off center loads. Available in capacities from 2 lbf. to 10 lbf. | | MBP Miniature Beam Overload Protected Load Cell
The MBP is the same as MB mini beam with internal overload protestion. It is a miniature beam load cell used in medical test machine and a variety of low capacity applications. Available in capacities from 2.5 lbf. to 10 lbf. |  | SMA Minature S-Type Load Cell
The SMC is miniature version of SM where height is a constraint. Available in capacities from 15 lbf. to 200 lbf. |  | SML Low Height Load Cell
The SML is a low height load cell with high performance. Available in capacities from 5 lbf. to 1K lbf. |  | U2B Force Transducer
The U2B is a force transducer that is suitable for measuring static or dynamic, tensile and compressive loads. Loading is applied utilizing the integral mounting studs. Ranges are available from 0.5kN to 200kN. |  | U9B Force Transducer
The U9B is a force transducer that is suitable for measuring static or dynamic, tensile and compressive forces. It is designed for assembly and production applications where space is at a premium. Ranges are available from 50N to 50kN. |  | WMC Miniature Sealed Stainless Steel Load Cell (1K-10K lbf)
The WMC is Interface's smallest tension & compression load cell. Available in capacities from 1K lbf. to 10K lbf. |  | WMC Miniature Sealed Stainless Steel Load Cell (5-500 lbf)
The WMC is Interface's smallest tension & compression load cell. Available in capacities from 5 lbf. to 500 lbf. | | Load Cells / Force Transducers - Multi-Axis | |  | 5200 Multi-Axis Load Cell
The 5200 Low Profile load cell is designed for applications where it is required to measure moment loads as well as axial load to determine center of gravity or misalignment. Available in capacities from 1K lbf. to 50K lbf. | | Load Cells / Force Transducers - Piezoelectric | |  | PACEline Piezoelectric Force Transducers (overview)
Your fitting and assembly processes are fast and space is a constraint. But you still expect consistently reliable quality control for your production. It’s time for PACEline. Compact and highly dynamic force measurement technology from HBM that makes the difference – and brings fresh impulses to piezo technology. |  | PACEline CFT Piezoelectric Force Transducer
CFT piezoelectric force transducers from HBM are available with measuring ranges from 5 to 120 kN enabling reliable, integrated force measurement, in particular where space is a constraint. The transducers are suitable for monitoring highly dynamic press-fit and assembly processes with fast force variations. |  | PACEline CMA Charge Amplifier
The PACEline CMA charge amplifier (analog amplifier) ensures reliable transmission of data from piezoelectric force transducers. This is done by signal conditioning to +/-10 V analog standard signals. |  | PACEline CMC - The piezoelectric force measurement chain
CFT piezoelectric force transducers and CMA analog amplifiers are combined to form a calibrated unit. Even with the most challenging task in your process monitoring: The CMC measurement chain keeps pace at any time. |  | PACEline CMD Digital Charge Amplifier
The digital charge amplifier for piezoelectric sensors assures multiple uses in many applications in the laboratory and production. The CMD600 measures very fast force, torque and pressure signals at frequencies of up to 30 kHz and can be used with piezoelectric sensors up to max. 600,000 pC (Pico coulombs). | | Load Cells / Force Transducers - S-Type | |  | SM S-Type Load Cell
The SM is a low cost highly accurate unsealed load cell for test machine and other general purpose applications. Available in capacities from 10 lbf. to 1K lbf. | | SMA Minature S-Type Load Cell
The SMC is miniature version of SM where height is a constraint. Available in capacities from 15 lbf. to 200 lbf. | | SML Low Height Load Cell
The SML is a low height load cell with high performance. Available in capacities from 5 lbf. to 1K lbf. |  | SMT S-Type Overload Protected Load Cell
The SMT is ideal for low capacity applications where loads cells are often inadvertently overloaded. The SMT has internal mechanical stops permitting overloads up to 10 times rated capacity. Available in capacities from 1.1 lbf. to 450 lbf. | | Load Cells / Force Transducers - Specialty | |  | EL20-S458 Belt Tension Load Cell
The EL20-S458 is a seat belt tension load cell, typically used for automotive crash test, military payload delivery, sport and military parachute tether loads, and automatic reserve chute deployment systems. Available in capacities of 1K lbf. to 3.2K lbf. |
| Mass Flow Sensors - Digital Mass Flow Meters & Controllers | |  | HFC-D-302 Digital Mass Flow Controller
The model HFC-D-302 digital mass flow controller features a fast response and a low pressure drop. It has RS232/485 communication and self-diagnostics, and a normally closed valve for flow control. Available in ranges from 0 - 5 to 0 - 25,000 sccm (N2 Equivalent). |  | HFC-D-303 Digital Mass Flow Controller
The model HFC-D-303 digital mass flow controller features a fast response and a low pressure drop. It has RS232/485 communication, self-diagnostics, and a normally closed valve for flow control. Available in ranges from 0 - 25 to 0 - 1,000 slm (N2 Equivalent). |  | HFC-D-307 Digital Mass Flow Controller
The model HFC-D-307 digital mass flow controller features a fast response and a low pressure drop. It has RS232/485 communication, self-diagnostics, and a normally closed valve for flow control.. Available in ranges from 0 - 1000 to 0 - 3000 slm (N2 Equivalent). |  | HFM-D-300 Digital Mass Flow Meter
The model HFM-D-300 digital mass flow meter features a fast response and a low pressure drop. It has RS232/485 communication and self-diagnostics. Available in ranges from 0 - 5 to 0 - 25,000 sccm (N2 Equivalent). |  | HFM-D-301 Digital Mass Flow Meter
The model HFM-D-301 digital mass flow meter features a fast response and a low pressure drop. It has RS232/485 communication and self-diagnostics. Available in ranges from 0 - 25 to 0 - 1,000 slm (N2 Equivalent). |  | HFM-D-305 Digital Mass Flow Meter
The model HFM-D-305 digital mass flow meter features a fast response and a low pressure drop. It has RS232/485 communication and self-diagnostics. Available in ranges from 0 - 1000 to 0 - 3000 slm (N2 Equivalent). | | Mass Flow Sensors - Mass Flow Meters & Controllers | |  | HFC-202 Mass Flow Controller
The model HFC-202 is a general purpose mass flow controller, which features a normally closed valve for flow control. Available in ranges from from 0 - 10 to 0 - 25,000 sccm (N2 Equivalent). |  | HFC-203 Mass Flow Controller
The model HFC-203 is a general purpose mass flow controller, which features a normally closed valve for flow control. Available in ranges from 0 - 30 to 0 - 500 slm (Air Equivalent). |  | HFC-302 Mass Flow Controller
The model HFC-302 mass flow controller features a fast response and a low pressure drop. It has a a normally closed valve for flow control. Available in ranges from 0 - 5 to 0 - 25,000 sccm (N2 Equivalent). |  | HFC-303 Mass Flow Controller
The model HFC-303 mass flow controller features a fast response and a low pressure drop. It has a a normally closed valve for flow control. Available in ranges from 0 - 25 to 0 - 1,000 slm (Air Equivalent). |  | HFM-200 Mass Flow Meter
The model HFM-200 is a general purpose mass flow meter. Available in ranges from 0 - 10 to 0 - 25,000 sccm (N2 Equivalent). |  | HFM-200 Mass Flow Meter with Laminar Flow Element
The model HFM-200 with an LFE provides fast, accurate measurement of high-capacity gas flows, in ranges from 25 slm up to 15,000 slm. The laminar flow elements are available in various sizes from 3/8" up to 8". Used in conjunction with the standard HFM-200, these units can be combined to measure full-scale flows up to 15,000 slm. |  | HFM-201 Mass Flow Meter
The model HFM-201 is a general purpose mass flow meter. Available in ranges from 0 - 30 to 0 - 500 slm (Air Equivalent). |  | HFM-300 Mass Flow Meter
The model HFM-300 mass flow meter features a fast response and a low pressure drop. Available in ranges from 0 - 5 to 0 - 25,000 sccm (N2 Equivalent). |  | HFM-301 Mass Flow Meter
The model HFM-301 mass flow meter features a fast response and a low pressure drop. Available in ranges from 0 - 25 to 0 - 1,000 slm (Air Equivalent). |  | HFM-305 Mass Flow Meter
The model HFM-305 mass flow meter features a fast response and a low pressure drop. Available in ranges from 0 - 1,000 to 0 - 2,500 slm (Air Equivalent). |  | HFM-306 Mass Flow Meter
The model HFM-306 mass flow meter features a fast response and a low pressure drop. Available in ranges from 0 - 2,500 to 0 - 8,000 slm (N2 Equivalent). |  | NALL Mass Flow Meter
The NALL series mass flow meter can withstand harsh environments up to 200°C, and have stainless steel construction. Available in ranges from 0-10 sccm up to 0-14,000 slm. | | Mass Flow Sensors - Mass Flow Meters for Hazardous Locations | |  | HFM-I-401 Mass Flow Meter
For harsh industrial environments. Has an IP65 enclosure & is approved for Class I, Div 2, Groups A, B, C & D. Comes in 0-10 slm to 0-350 slm (N2 equivalent). |  | HFM-I-405 Mass Flow Meter
For harsh industrial environments. Has an IP65 enclosure & is approved for Class I, Div 2, Groups A, B, C & D. Comes in 0-100 slm to 0-2500 slm (N2 equivalent). | | Mass Flow Sensors - OEM Mass Flow Meters | |  | Customized Mass Flow Meters and Mass Flow Controllers for OEM Applications
Customized mass flow meters and controllers are possible for large quantity applications. Specifications will depend on application requirements. | | Mass Flow Sensors - Powerpods (Power Supply/Digital Indicator) | |  | NALL Indicator & Power Supply
The NALL power supply features a bright digital display and is contained in either a cabinet or panel mountable case. All models feature high accuracy and excellent repeatability. Operates with the NALL mass flow meter. | | THPS-100 Single Channel PowerPod
The THPS-100 is a self-contained power supply and display designed for gas mass flow-meters. It features an automatically generated set point (0-5V or 0-10V) and RS232 communication. | | THPS-400 Four Channel PowerPod
The THPS-400 is a power supply and indicator capable of displaying four channels simultaneously. It has an integrated totalizer, filter function, and Serial communication. Has the ability to set ratio control for gas blending applications. |
| Piezo Film - Instrumentation | |  | Piezo Film Lab Amplifier
The Piezo Film Lab Amplifier is a versatile preamplifier for use with Piezoelectric sensors. Provides a wide range of sensitivity adjustment in either voltage or charge modes, and the functionality of the high- and low-pass filters. | | Piezo Film - Piezo Cable | |  | Piezo Polymer Coaxial Cable
Piezo cable is another form for piezo polymer sensors. Designed as a coax cable, the piezo polymer is the "dielectric" between the center core and the outer braid. When the cable is compressed or stretched, a charge or voltage is generated proportional to the stress. | | Piezo Film - Piezo Film Elements | |  | CM-01B Contact Microphone
The CM-01B Contact Microphone uses sensitive but robust PVDF piezo film combined with a low-noise electronic preamplifier to provide a unique sound or vibration pickup with buffered output. |  | DT Series
The DT Series of piezo film sensors elements are rectangular elements of piezo film with silver ink screen printed electrodes. They are available in a variety of different sizes and thicknesses. |  | DT Series with Lead Attachments
The DT Series of piezo film sensors elements are rectangular elements of piezo film with silver ink screen printed electrodes, and leads attached. They are available in a variety of different sizes and thicknesses. |  | FDT Series
The FDT Series of piezo film sensors elements are rectangle elements of piezo film with silver ink screen printed electrodes, and flexible leads attached. The piezo polymer tail extends from the active sensor area as flex circuit material with offset traces. |  | LDT Series
The LDT series has a 0.005" (125µm) polyester layer is laminated to a 28 µm or 52µm piezo film element. When used in a 'bending' mode, laminated film elements develop much higher voltage output when flexed than a non-laminated DT elements series. |  | LDT1-028K with Lead Attachments
The LDT1-028K is a multi-purpose, piezoelectric sensor for detecting physical phenomena such as vibration or impact. The piezo film element is laminate to a sheet of polyester (Mylar), and produces a useable electrical signal output when forces are applied to the sensing area. | | Piezo Film - Piezo Film Sheets | |  | Metallized Piezo Film Sheets
Piezo film is available in a variety of different film sizes and thicknesses. These can be fabricated into simple transducers, or for use as full size sheets for applications such as speakers. | | Piezo Film - Piezo Switches and Ultrasonic Sensors | |  | NDT1-220K Ultrasonic Transducer
The NDT1-220K element offers outstanding ultrasonic transducer performance in a low-cost, flexible format for general-purpose use. The transducer is robust, and conforms perfectly to cylindrical surfaces such as pipe or tank walls. |
| Pressure Sensors & Transmitters - Board Mountable / OEM | |  | 17 UltraStable Pressure Sensor
The Model 17 Ultrastable is a high performance, temperature compensated, piezoresistive silicon pressure sensor packaged in TO-8 configurations. It uses Measurement Specialties’ proprietary ultrastable die to provide excellent performance and long-term stability over wide temperatures. Gage and absolute pressure ranges from 0-15psi to 0-250psi are available. |  | 27 UltraStable Pressure Sensor
The Model 27 is a high performance, temperature compensated, piezoresistive silicon pressure sensor packaged in a bottom tube TO-8 configuration. It provides excellent performance and long-term stability. Gage pressure ranges from 0-15psi to 0-250psi are available. |  | 37 UltraStable Pressure Sensor
The Model 37 is a high performance, temperature compensated, piezoresistive silicon pressure sensor packaged in a differential TO-8 configuration. It provides excellent performance and long-term stability. Differential pressure ranges from 0-15psi to 0-250psi are available. |  | 47 UltraStable Pressure Sensor
The Model 47 is a temperature compensated, piezoresistive silicon pressure sensor packaged in TO-8 configurations. It provides excellent performance and long-term stability. Gage and absolute pressure ranges from 0-2psi to 0-250psi are available. |  | Ares Pressure Sensor
The ARES Series is a small, low cost pressure transducer which is able to measure pressures as low as 0 to 5 inches of water, 0 to 10" of water, 0 to 15" of water, and 0 to 1 psi. Sensitivity to extremely low pressures and small size make this device ideally suited for HVAC, medical equipment, and flow monitoring applications. The GA100 series has a 4V span from 0.50V to 4.50V and the GA200 series has a 3.75V span from 0.25V to 4.00V. |  | MS5540C Pressure Sensor
The MS5540C is a SMD-hybrid device including a precision piezoresistive pressure sensor and an ADC Interface IC. It is a miniature version of the MS5534C barometer/altimeter module and provides a 16-bit data word from a pressure and temperature dependent voltage. MS5540C is a low power, low voltage device with automatic power down (ON/OFF) switching. | | Pressure Sensors & Transmitters - Pressure Sensor Elements (Headers) | |  | 86A Pressure Sensor
The Model 86A is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. Designed for o-ring mounting. A custom ASIC is used for temperature compensation, offset correction, and provides an amplified output of 0.5 to 4.5V. Available in 0 - 1 up to 0 - 150 PSIG ranges. |  | 87N UltraStable Pressure Sensor
The Model 87N UltraStable™ is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 87N UltraStable™ is offered in a weldable package or with a variety of threaded fittings such as 1/4 and 1/8NPT, 1/4BSP as well as custom process fittings. Available in 0 - 1000 up to 0 - 5000 PSI ranges, in absolute and sealed gage versions. |  | 89C UltraStable Pressure Sensor
The Model 89 UltraStable™ (compensated) is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 89 UltraStable™ features 5/16-32 UNEF threads and can be welded in place. It can also be packaged in a variety of threaded fittings such as 1/4 and 1/8NPT, 1/4BSP. Available in 0 - 1000 up to 0 - 5000 PSI ranges, in absolute and sealed gage versions. |  | 89CV UltraStable Pressure Sensor
The Model 89 UltraStable™ (constant voltage) is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 89 UltraStable™ features 5/16-32 UNEF threads and can be welded in place. It can also be packaged in a variety of threaded fittings such as 1/4 and 1/8NPT, 1/4BSP. Available in 0 - 1000 up to 0 - 5000 PSI ranges, in absolute and sealed gage versions. |  | 89U UltraStable Pressure Sensor
The Model 89 UltraStable™ (uncompensated) is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 89 UltraStable™ features 5/16-32 UNEF threads and can be welded in place. It can also be packaged in a variety of threaded fittings such as 1/4 and 1/8NPT, 1/4BSP. Available in 0 - 1000 up to 0 - 5000 PSI ranges, in absolute and sealed gage versions. |  | DP86 Differential Pressure Sensor
The DP86 differential pressure sensor is a double-sided, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The DP86 is designed for O-ring mounting. Available in ranges from 0 - 1 up to 0 - 500 PSID. | | Pressure Sensors & Transmitters - Pressure Transducers | |  | EPB Pressure Sensor Probe
EPB is a small pressure probe sensor, small profile, stainless steel, flush mount transducer designed for general media. EPB is offered in pressure ranges from 0-5 to 5000 psi (0-0.35 to 350 bar), vented, sealed, and absolute pressure. |  | EPIH Subminiature Pressure Sensor
The EPIH is a subminiature pressure sensor, specifically designed for Dynamic and High Frequency measurements with resonant frequency up to 1.7 MHz. Available with many various housings, EPIH is one of the smallest pressure sensors in the world. |  | EPL Miniature Surface Mount Pressure Sensor
The EPL is a surface mount pressure sensor with a stainless steel diaphragm. Available in ranges from 5 to 5000 psi (0.35 to 350 bar), EPL is easy to install on flat surfaces using elastomer or epoxy. |  | EPX Miniature Pressure Sensor
The EPX is a miniature threaded pressure sensor with stainless steel flush diaphragm compatible with general media. Threads M5x0.8 or 10-32 UNF are available with built-in 0-ring seal for an easy installation. The EPX is offered in many pressure ranges from 0.35 to 350 bar (5 to 5000 psi) with gage, sealed gage, or absolute pressure reference. |  | EPXN Pressure Sensor
The EPXN is a high performance small pressure sensor using silicon chip for clean media (non corrosive). With it's recessed port, it is best recommended for static applications or low frequency. Offered in pressure ranges from 0 - 5 up to 0 - 150 PSI. |  | EPXO Pressure Sensor
The EPXO is a high performance unit with a stainless steel flush diaphragm. It is designed for high temperature, high stability, and high sensitivity applications. The EPXO is offered in pressure ranges from 0 - 150 up to 0 - 7500 PSI in gage (vented), sealed gage, and absolute pressure. |  | LM Liquid Level Pressure Transducer
The LM Series incorporates stainless steel and plastic isolation suitable for level sensing in water, other liquid and gas. It uses a stainless steel sensor in a PVC plastic fitting, and provides an output of .5V to 4.5V with a 5V supply. Available in 0 - 1 up to 0 - 150 PSIG ranges. |  | M5100 MicroFused Pressure Transducer
The M5100 sets the price / performance standard for transducers used in demanding environments. The pressure port is machined from a solid piece of 17-4PH stainless steel. There are no O-rings, organics or welds exposed to the pressure media. Available in ranges from 0 - 50 up to 0 - 10,000 PSIG. |  | U5100 UltraStable Pressure Transducer
The UltraStable™ technology employs a silicon-based strain gauge isolated by an oil-filled capsule and a stainless steel diaphragm. The U5100 features 100% 316L media isolation, excellent long term stability, and 0.1% FS combined accuracy. Available in ranges from 0 - 15 up to 0 - 10,000 PSI, in gage and absolute pressure. |  | US10000 UltraStable Pressure Transducer
The US10000 Series from MEAS is the first choice for applications requiring high accuracy in a rugged environment. The 0.05% accuracy and typical total error band of 0.25% provides a stable platform for test stands and high accuracy industrial pressure applications. Available in ranges from 0 - 5 up to 0 - 10,000 PSI, in gage and absolute pressure. |  | US300 UltraStable Pressure Transducer
The UltraStable™ technology employs a silicon-based strain gauge isolated by an oil-filled capsule and a stainless steel diaphragm. The US300 incorporates stainless steel isolation, and a wide range of standard pressure ranges and electrical outputs in a very compact package. Available in ranges from 0 - 15 up to 0 - 5,000 PSI, in gage and absolute pressure. | | Pressure Sensors & Transmitters - Vacuum | |  | IGE-3000 Ionization Gauge
The Teledyne Hastings Instruments IGE-3000 line of Ionization Gauge Tubes and Electronics provides the user with accurate, repeatable pressure measurement starting in the medium vacuum range and continuing through into the ultrahigh vacuum range. Range: 10-9 Torr to 10-2 Torr |
| Rotary Position Sensors - Hall Effect | |  | NRH280 Noncontact Rotary Hall Sensor
Rotary position sensor that features a 2-piece unit - fully sealed sensor assembly and magnetized bolt. Single or dual outputs available. |  | SRH220DR Contactless Rotary Sensor
SRH220DR provides reliable and accurate rotary position measurement in extreme industrial environments, such as specialist off-highway construction and agricultural vehicles, where shock, vibration and extreme temperatures can occur. It is housed in an all-new moulded housing with separate supply voltage and output signals on two channels. Environmental protection to IP67/IP68 is dependent on the connector style selected. |  | SRH280P & SRH280DP Contactless Rotary Position Sensor
For extreme motorsport and industrial environments where shock and vibration can occur. Uses 28mm flanged housing with protection rating to IP68. | | Rotary Position Sensors - Magnetic Encoder | | | ED-18 Magnetic Encoder
The ED-18 Series magnetic encoder can be used as either a rotational feedback sensor or as a human machine interface (HMI) device. As a light duty feedback sensor it can provide rotation speed, direction or positioning information. The analog output provides absolute angular position information even when power is cycled on and off. As an HMI device it can be used as a rotary input control for use on instrumentation panels. | | ED-19 Magnetic Encoder
The ED-19 Series magnetic encoder is designed for medium duty feedback applications. Resolutions are available from 64 to 1024 counts per revolution. The magnetic technology used in the ED-19 series is plug-in compatible with existing encoder products, with the added advantages of an extended temperature range and fully sealed electronics. The ED-19 suffers no LED degradation, meaning it has a virtually unlimited life. | | ED-20 Magnetic Encoder
The ED-20 Series magnetic encoder is designed for medium duty industrial feedback applications with ball bearing supported shaft. Resolutions are available from 200 to 1024 counts per revolution. This encoder series also features line drivers with active termination for long cable runs and reverse voltage protection. The ED-20 also offers the option of high voltage differential, low voltage differential or open collector (NPN) outputs. | | ED-21 Magnetic Encoder
The ED-21 Series magnetic encoder is designed to replace traditional mechanical potentiometers. This product is offered with a ball bearing supported shaft. Five standard output ranges are available: 0.5 - 4.5v, 0 - 5v, 0 - 12v, 4 - 20mA and 0 - 20mA. The magnetic technology used in the ED-21 offers advantages over conventional electromechanical potentiometers with sealed electronics, extended temperature ranges, and virtually unlimited life. | | ED-22 Magnetic Encoder
The ED-22 Series magnetic potentiometer can be used to replace a conventional potentiometer. This product offers 270 degrees of electrical travel, integrated rotational stop system, 300 degrees of mechanical travel, utilizing a sleeve bearing and shaft fitted with an O-ring seal. The non-contact magnetic sensor design utilized in the ED-22 is well suited for industrial applications with temperature extremes, high vibration and shock, and contamination. | | Rotary Position Sensors - Potentiometers | |  | SRS280 Sealed Rotary Potentiometer
The SRS280 was developed to meet the harsh operating requirements of today´s automotive and motorsport markets. It uses hybrid potentiometer track technology, providing high stability under extremes of temperature and humidity |
 | 500 In-Line Signal Conditioner
Small, DC powered in-line signal conditioner with 9-pin connectors, +/-5V and 4-20mA outputs and 1000Hz bandwidth. |  | ATA-2001 Amplifier
The Measurement Specialties analog transducer amplifier is a general purpose, AC line-powered LVDT/RVDT conditioner featuring state-of-the-art design principles. All amplifier controls are accessible from the outside of the rugged aluminum enclosure. Designed for universal compatibility with all 4, 5, and 6 lead LVDTs. A wide range of oscillator frequencies combined with two excitation voltages, 3.5 and 0.5 Vrms, provide maximum versatility. |  | DCA Signal Conditioner
10-28V supply and user selectable +/-10V, +/-5V or 4-20mA output in a small NEMA 4X sealed ABS enclosure. Features 100Hz bandwidth. |  | DF30CAN digiCLIP Digital Amplifier
digiCLIP is the modern modular amplifier system for industrial environments. The model DF30CAN is compatible with strain gauge transducers, and features a CANbus digital interface and TEDS sensor recognition. |  | DF30DP digiCLIP Digital Amplifier
digiCLIP is the modern modular amplifier system for industrial environments. The model DF30DP is compatible with strain gauge transducers, and features a Profibus DP digital interface and TEDS sensor recognition. |  | DF31CAN digiCLIP Digital Amplifier
digiCLIP is the modern modular amplifier system for industrial environments. The model DF31CAN is compatible with strain gauge transducers, and features a CANbus digital interface and TEDS sensor recognition. Also features 1 digital input and 2 digital outputs. |  | DF31DP digiCLIP Digital Amplifier
digiCLIP is the modern modular amplifier system for industrial environments. The model DF31DP is compatible with strain gauge transducers, and features a Profibus DP digital interface and TEDS sensor recognition. Also features 1 digital input and 2 digital outputs. |  | digiCLIP Digital Amplifier (overview)
digiCLIP is the modern modular amplifier system for industrial environments. It facilitates faster and more reliable measurement, and it’s easily installed. digiCLIP also recognizes transducers equipped with TEDS memory chips. CANbus and PROFIBUS interfaces available. |  | DMA Signal Conditioner
Din rail mountable with user selectable outputs of +/-10V, +/-5V or 4-20 mA. 10-28VDC powered suitable for battery or automotive use. Features 1000 Hz bandwidth and push-button shunt calibration. |  | EICT Signal Conditioning Module
The EICT signal conditioning module has been specifically designed to operate with the ICT and SLT190 range of contactless linear position transducers. The module operates from a 10-60 Vdc supply voltage and provides a range of outputs which can be configured by the user. |  | INF-USB Universal Serial Bus Output Module
The INF-USB module allows measurements from load cells, torque sensors, or other sensors to be acquired by USB. System also includes graphing and logging software. |  | LDM-1000 Signal Conditioner
The LDM-1000 features several different input / output options to accommodate varying PLC analog I/O requirements. A wide range combination of gains, drive voltages and oscillator frequencies insure compatibility with virtually all LVDT and RVDT type sensors. |  | MP01 Multi Channel PME Amplifier
Multi-channel amplifier for applications in process supervision and industrial test-rig measurement technology. |  | MP55 Single Channel PME Amplifier
4.8kHz carrier frequency for S.G., inductive, LVDT, piezo-resistive, and potentiometric transducers. |  | MP55DP Single Channel PME Amplifier
4.8kHz carrier frequency for S.G., inductive, LVDT, piezo-resistive, and potentiometric transducers with DP interface. |  | MP60 Single Channel PME Amplifier
Single channel module for incremental transducers. |  | MP60DP Single Channel PME Amplifier
Single channel module for incremental transducers with Profibus DP interface. |  | PME Industrial Amplifiers
The PME range of products offer different types of modules for recording of all measured quantities relevant to processing, such as force, displacement, pressure, temperature, speed, frequency and torque. All measuring modules come with an LCD display, keypad and a CAN interface, 4 digital I/Os, changeover analog output (+/- 10V, 4...20 mA, +/- 20 mA), 4 limit value switches, 2 peak value stores and 4 parameter set memories. |  | SCM100 Signal Conditioner
The SCM100 LVDT signal conditioning module has been designed specifically to operate with the AF111 and AF145 range of LVDTs, and to make using an LVDT as simple as using a linear potentiometer. Capable of providing a range of voltage or current output signals. |  | SGA Signal Conditioner
User selectable outputs of +/-10V, +/-5V, 0-10V, 0-5V, 0-20mA and 4-20ma. DC or AC powered with switch selectable filters from 1 to 5kHz & sealed ABS enclosure. Supports shunt calibration & a wide range of gain settings. |  | SSC Signal Conditioning Module
The new Penny+Giles model SSC is a Sensor Signal Conditioning unit housed in an IP68 protected metal enclosure. It is suitable for use with any sensor that produces a dc output signal voltage in the range 0 - 5Vdc. The SSC also provides a 5Vdc source that may be used as a supply for many types of sensors. |  | UCM Universal Signal Conditioner
The new Penny+Giles model UCM is a low voltage dc powered Universal Conditioning Module designed to operate with a wide range of LVDTs, RVDTs and other analogue inductive transducer types. The set-up is simple and flexible, allowing user adjustment of excitation voltage and frequency, operating mode, span output and zero position, as well as configuration for multiple unit synchronisation. | | Signal Conditioning - Distributed IO | |  | ioPro Distributed IO
The ioProTM family provides a comprehensive set of DIN high density rail mount IO modules for any Modbus-RTU application. Based on the successful ioPak family, but with new features and improved performance. | | Signal Conditioning - Wireless | |  | EtherWave™ WMR-900
The EtherWave WMR allow you to build your own long-range, non-line-of-sight, point-to-point or point-to-multipoint wireless Ethernet solution that can enable fringe Ethernet devices, including SCADA clients, remote
instruments, bio-scanners, printers, PCs, VoIP phones, point-of-sale devices, digital signage, or Internet kiosks. |
| Software - Data Analysis Software | |  | GlyphXE Analysis Software
Integrated and powerful analysis methods for post-processing of your measured data make GlyphXE the technically mature, professional tool for your test projects. At the same time, GlyphXE convinces through maximum ease of use - even for occasional users. GlyphXE provides a graphical user interface that enables you to develop individual analyses and computations step by step. No programming knowledge or learning of a special script language is required. |  | InField Software
InField is a versatile field analysis software program optimized for use with SoMat hardware. It is designed to enhance the field test collection and data visualization process by making sure you never leave the field without the numbers you need. | | Software - Fatigue & Durability Software | |  | Automation Software
nCode Automation captures, manages, distributes, and performs in depth-analyses of time-dependent data within a common, collaborative environment. It is a web-based system - simple to deploy, configure and use. No software coding is required and nCode Automation is hardware independent. Complex analysis process can be developed using GlyphWorks on the desktop and uploaded to the nCode Automation server. Queries and reports can be readily based on all the analysis results. Detailed bespoke web reports are now possible on all engineering data, without having to move large data files around IT networks. |  | GlyphWorks
nCode GlyphWorks is the leading data processing system for engineering test data analysis. Designed to handle huge amounts of data, GlyphWorks provides a graphical, process-oriented environment. Users can simply create an analysis workflow by ‘drag and dropping’ analysis building blocks. | | Software - Measurement Software | |  | Catman AP Software
Benefit from the new generation of data acquisition software. catman®AP bundles highly efficient modules for many different measurement tasks. Each module is a champion in its specific field of application. The modules in combination provide a flexible, powerful, and networked high-performance package – catman®AP. |  | Catman Easy Software
With catman®Easy you can perform a large number of different measurement tasks quickly and simply... without wasting time or effort on programming. Thanks to the optimal interaction between hardware and software, you can configure your amplifier much faster. You can also quickly define your measurement parameters such as sampling rates, trigger settings, as well as select your preferred visualization mode. |  | Catman Enterprise Software
The catman®Enterprise software suite was specifically developed for high channel-count measurement using the MGCplus DAQ system. A dedicated measurement-data server (MDS) performs the actual measurement. You can connect a number of client PCs to simultaneously access data on the MDS server. This enables you to monitor and evaluate your high channel-count measurement processes in real time. |  | Catman Professional Software
Catman®Professional enables you to easily configure connected amplifiers and intuitively define, run and automate your measurement sequences without any programming knowledge. Measured values can be visualized in real time or after measurement has been concluded for reporting purposes. Recurring measurement tasks are greatly simplified as catman® can be used to automate each sequence. |  | Perception Software
Perception is a modularly structured software package for high speed measurement data acquisition and it accomplishes all tasks in the measurement sequence: Parameterization of sensors and control of measurement instruments, Real-time display of measured values, Storage and playback, and Analysis and report generation. The special features in Perception enable rapid setup times, rapid familiarization and therefore the immediate start of the measurement campaign. |  | Perception Software - advanced exports
For off-line analysis using third-party software packages, Perception offers a variety of export formats for many popular programs. Extensive built-in set-up options let you export the data of interest the way you want, and nothing more. In addition, these exports can be combined with the powerful automation and post processing features included as standard in Perception. |  | Perception Software - analysis
Within Perception, customers can define their own formulas to compute results in seconds rather than hours. A "formula database" is used to enter math expressions like CH1*CH2 or MAX@CH1 to compute results immediately when new data arrives. The formula results can be re-used in other formulas to get even more advanced answers. |  | Perception Software - basic FFT
The Perception software not only offers a powerful and extremely fast time domain display of live and stored data, the Basic FFT option also enables to transfer the data into the frequency domain and to display amplitudes over frequency. Therefore the user can obtain valuable information about the content of mixed signals like vibrations, shocks or noisy signals beyond what is visible in a time domain display. |  | Perception Software - HPHV automated analysis
The testing of HV and MV switchgear devices requires advanced and automated analysis capabilities to generate
reproducible and accurate test results. The operator’s interaction at this stage of the signal evaluation should be minimal. Real world signals may be distorted, carry noise or spikes, but they still have to be evaluated appropriately and in an automated manner. |  | Test Control Environment (TCE) Software
SoMat Test Control Environment (TCE) is the Microsoft Windows-based® test control and setup interface software that is supplied with every eDAQ and eDAQ-lite data acquisition system. |
| Strain Gauges - Accessories | |  | DAK1 Strain Gauge Starter Kit
The starter kit DAK1 provides the first time user with a low cost and interesting option to start with the application of strain gauges. The well-designed and robust plastic case contains all aids required for initial applications. |  | DAK2 Strain Gauge Installation Case
The strain gauge installation case DAK 2 contains all tools and aids required for strain gauge installations. It is portable and lockable. Dimensions: 470 x 170 x 360 mm Weight: approx. 6 kg (incl. standard scope of delivery). |  | LS Solder Terminals
Terminal strips for mounting the strain gauge leads and connecting cabling. |  | RMS1 Cleaning Solvent
Satisfactory bonding joints are only achieved if the adhesive covers the bonded surfaces well. Therefore, the application surfaces must be cleaned prior to bonding with a chemically pure solvent and a clean cleaning pad. RMS1 is an environmentally friendly mixture of Isopropanol and Acetone which dissolves all normal contamination. | | Strain Gauges - Adhesives | |  | BCY01 Accelerator for Z70
BCY01 is an activator for the Z70 cyanacrylate adhesive. The curing of Z70 depends on the chemical state of the parts to be joined. There are conditions where curing may take place slowly or even remain incomplete; such as dry air (relative humidity below 40%), acid surfaces or too low temperature. In these cases the curing time can be shortened with the BCY01 activator. |  | EP150 Hot-Curing Single Component Adhesive
Epoxy resin adhesive that can be used with all types of strain gauges. Storage time(dry): 12 months in refrigerator (+7°C). Application temperature range: -70°C ... +150°C with zero-point related measurements (static) and with non zero-point related measurements (dynamic). |  | EP250 Hot-Curing Two Component Adhesive
EP250 is a two-component epoxy resin adhesive. EP250 is of pasty consistency and so it is suitable for porous surfaces as well as for smooth ones. For curing it requires heat and pressure. |  | EP310S Hot-Curing Two Component Adhesive
EP310 is a two-component epoxy resin adhesive. For curing it requires heat and pressure. EP310 is of watery liquid consistency and so it is suitable only for non-porous surfaces. |  | X280 Cold-Curing Two Component Adhesive
X280 is a two-component epoxy resin adhesive. As a cold curing adhesive it is easy to use and can be processed at minimum cost and effort. It hardens under normal ambient conditions. X280 is suitable for smooth and absorbent surfaces. |  | X60 Cold-Curing Two Component Adhesive
X60 is a 2-component fast curing adhesive, consisting of a liquid component (B) and a powder (component A). Typical application fields are: low temperature, porous materials as well as for securing the cables. |  | Z70 Cold-Curing Single Component Adhesive
Z70 is a single component, cold curing adhesive made of cyanacrylate. Curing is only possible on very slight adhesive films and at room temperature under thumb pressure. The air humidity needs to be between 40% and 70% as a catalyst for the curing process. | | Strain Gauges - Low Cost Strain Gauges | |  | Showa Strain Gauges - general specifications
Low cost strain gauges suitable for structural strain measurement in civil engineering laboratories and other general purpose applications. Available in uniaxial, biaxial, triaxial, and specialty versions in a variety of patterns. |  | Showa Solder Terminals & Adhesives
Select solder terminals and adhesives suitable for your strain gauge application. |  | Showa Strain Gauges
Find the specific part number of the strain gauges according to your application. | | Strain Gauges - Optical Strain Gauges | |  | Optical Strain Gauges
Benefit from the many new advantages of measuring with light - without having to abandon the ruggedness and convenience of the classical strain gauge. HBM's optical strain gauges are made from fibers of glass with a very small core diameter of no more than 5 micrometers. In comparison, the diameter of human hair ranges from 60 to 80 micrometers. The fiber core is surrounded by a cladding layer from purest glass with a diameter of 125 micrometers. |  | DI Series Optical Interrogators
Now you can also benefit from perfectly matched measurement chains when using optical strain gauges. Gain time and increase safety by utilizing the complete solution from a single source - from optical strain gauges through interrogators (opto-electric measurement instruments) and software. DI Interrogators are for dynamic measurements. |  | SI Series Optical Interrogators
Now you can also benefit from perfectly matched measurement chains when using optical strain gauges. Gain time and increase safety by utilizing the complete solution from a single source - from optical strain gauges through interrogators (opto-electric measurement instruments) and software. SI Interrogators are for static measurements. |  | EasyOptics module for CatmanAP software
HBM’s EasyOptics module for the catman®AP enables you to simultaneously acquire and visualize signals from optical and electrical strain gauges giving critical help when comparing different strain gauge measurements. |  | M408 - M416 Multiplexer for optical strain gauges
A single HBM multiplexer increases the number of optical sensor chains - and measuring points - that can be connected by up to a factor of 4. Instead of "cascading" several interrogators in series, multiplexers allow for extremely simple installation of your test setup - and at the same time provide a distinct cost advantage. | | Strain Gauges - Protective Coatings | |  | ABM75 Aluminum Foil c/w Kneading Compound
ABM75 is an aluminum foil c/w kneading compound for sealing. Recommended to use in conjunction with AK22. Supplied in 11 pcs of 205mm x 100mm. |  | AK22 Viscous Putty
AK22 is a tough, kneadable putty, strongly adhering on nearly every material. At very high accelerations (e.g. stroke or fast rotation) the AK22 may move its position because of its high mass. AK22 does not harden so there is no question of its hindering movement at the gauge area. An optimum protection can be reached by putting a layer of ABM75 on top of the AK22. | | Strain Gauges - Strain Gauges | |  | C Series Strain Gauges
The specialist for extreme temperatures. |  | LE11 Encapsulated Strain Gauge
Encapsulated strain gauge with stranded wire - moisture proof and resistant against chemicals. |  | LI66 Fiber Composite Material Strain Gauges
LI66 strain gauges for integration in fiber composite materials. |  | LY11 Micro Strain Gauge
LY11-0.3/120 micro strain gauges: Certainty, even if every millimeter counts. Ever smaller, ever more performance: The trend toward miniaturization of components is an ongoing challenge. Where every millimeter counts, the new 1-LY11-0.3/120 micro strain gauge ensures significant reliability while requiring only a minimum of space. |  | Pre-Wired Strain Gauges
Strain gauges with connection cable and optional RJ11 plug. For experimental stress analysis, HBM has introduced a series of strain gauges with pigtails, based on the series that has proved its worth in stress analysis, the Y-series. The pre-wired strain gauges are provided with 50 mm-long teflon-insulated connection wires. These strain gauges are specifically customized with optional pigtail lengths (0.5 m to 10m) connected in 2, 3 or even 4-wire circuits. |  | RDS Crack Propogation Gauges
Crack propagation gauges - RDS20, RDS22, RDS40. Using crack propagation gauges, it is possible to determine the crack propagation on a component. |  | V Series Strain Gauges
Encapsulated strain gauges with 3m stranded connection wire. |  | Y Series Strain Gauges
General purpose gauges for most experimental stress analysis applications. | | Strain Gauges - Temperature Sensor | |  | TT-3-100 Temperature Sensor
The temperature sensor that is installed as easily as a strain gauge. TT-3/100 is a temperature sensor that can be used as easily and flexibly as a classical strain gauge. TT-3/100 is the ideal choice, if your measurement task involves measuring strain in particular - and, additionally - temperature values. |
 | AccuStar Electronic Clinometer
The AccuStar® Electronic Clinometer is an extremely accurate angle measurement device. Designed for easy integration, with a choice of analog, ratiometric, digital or serial models, the clinometer produces an output signal corresponding to direction and magnitude of angular displacement. Features a linear range of ±45°. |  | LCI Inclinometer
The Jewell LCI Series Inclinometer is a ±14.5º to ±90º device designed for low frequency tilt sensing applications. LCI units are characterized by excellent turn on repeatability and very low hysteresis. |  | LCI-360 Inclinometer
The JEWELL LCI-360 is a biaxial inclinometer that meets the needs of high accuracy applications with low shock and vibration. The LCI employs a torsion flexure suspension that offers superior repeatability and low hysteresis at low frequencies. |  | LSR Inclinometer
The JEWELL LSR Series Inclinometer meets the needs of applications with space constraints. The compact, cylindrical shape and the "stacking" feature of the LSR facilitate the use of several inclinometers when multi-axis measurement is required. The LSR inclinometer offers the same precise readings with high outputs at lower range frequencies as our LSO Series. |  | NS-10E2 Inclinometer
This dual axis Inclinometer uses two single axis, tilt sensors. The sensor works on the conductivity principle. Features a range of ±10° and a voltage output. |  | NS-15E Inclinometer
This dual axis Inclinometer uses two single axis, tilt sensors. The sensor works on the conductivity principle. Features a range of ±15° and a voltage output. |  | NS-45E2 Inclinometer
This dual axis Inclinometer uses two single axis, tilt sensors. The sensor works on the conductivity principle. Features a range of ±45° and a voltage output. |  | NS-5E2 Inclinometer
This dual axis Inclinometer uses two single axis, tilt sensors. The sensor works on the conductivity principle. Features a range of ±5° and a voltage output. |  | NS-P Inclinometer
The P-series inclinometers are microprocessor controlled transducers capable of producing a linearized RS-232 digital or analog voltage output. They feature an aluminum baseplate and IP 65 housing, and are ideal for industrial, automotive and aerospace applications. Available in various ranges up to ±45°. |  | STT280 Sealed Tilt Sensor
The STT280 is provided in an extremely compact housing, for the most arduous operating environments. It is suitable for applications such as road construction equipment, cranes and booms, scissor lifts, agricultural vehicles, container handling and hydraulic lift systems. |
| Torque Sensors - Non-Contacting / Torque Flanges | |  | CS-T-08 Flexplate Torque Transducer
Special Torque Transducer which replaces the original flexplate |  | T10F Torque Flange
The T10F torque flange is the first torque flange representative. The T10F uses shear stress as a measure of torque for the first time, a measurement principle for which HBM applied for patent. Available in ranges from 50 N·m up to 10 kN·m. |  | T10FM Torque Flange
The T10FM torque flange can measure torques up to 80 kN·m. It is based on a modified T10F measuring body and also uses the shear stress principle of measurement. The measuring body and the torque introduction part are made from one piece. Its extremely short design takes up less space in the test rig and thus saves money. The high permissible transverse forces allow projecting machine elements to be directly connected. |  | T10FS Torque Flange
The T10FS torque flange adds to the outstanding market reputation of the T10F torque flange, extending the range covered to greater accuracy, higher speeds and smaller outside diameters. It is based on a modified T10F measuring body and also uses the shear stress principle of measurement. Available in ranges from 100 N•m up to 10 kN•m. |  | T12 Digital Torque Flange
Uses modern fieldbus systems (CANopen, PROFIBUS DPV1) for connecting directly to PLC automation systems. Provides a frequency & analog output. Fit for use with conventional technologies. |  | T20WN Torque Transducer
The T20WN torque flange is specifically designed for measuring static and dynamic torque, rotation speed and angle of rotation in the laboratory, test and inspection sector, as well as in production monitoring and quality assurance. Avaiable in ranges from 0.1 N•m to 200 N•m. |  | T22 Torque Transducer
The T22 is an attractively priced transducer for simple torque applications. It comes with integrated electronics; this saves time and costs – no additional, external amplifiers are required for upgrading your measurement chain. Matched couplings are available for all T22 sizes. Its' compact design is perfectly suited for test benches where space is a constraint. |  | T40 Torque Flange
Saves space & costs due to its short design. Allows high parasitic loads enabling machine elements to be directly mounted. Has no slip rings or bearings. Available from 200 N·m to 10 kN·m. | | Torque Sensors - Slip-Ring | |  | T5 Torque Transducer
The T5 torque transducer is designed for occasional, simple torque measurement tasks in the laboratory, teaching and testing sector. The cylindrical shaft ends allow torque to be applied without play. Slip-ring transfer allows all industry-standard amplifiers for SG full bridges to be used. Available in ranges from 10 N•m to 200 N•m. |
| Vacuum Pressure Sensors - Ionization Gauges | | | IGE-3000 Ionization Gauge
The Teledyne Hastings Instruments IGE-3000 line of Ionization Gauge Tubes and Electronics provides the user with accurate, repeatable pressure measurement starting in the medium vacuum range and continuing through into the ultrahigh vacuum range. Range: 10-9 Torr to 10-2 Torr |
| Weighing - Digital Load Cells | |  | HBM Digital Load Cells
Digital load cells on the basis of the strain gage technology provide new impetus for the areas of dynamic weighing, sorting, filling, and dosing. | | Weighing - Electronics | |  | 9300 Weight Indicator
6-digit unipolar display in a rugged NEMA 4X stainless steel washdown enclosure. Able to power up to 8 load cells, the 9300 is an excellent choice for scales and weighing use. Featuring front panel tare and Net/Gross buttons, 3-stage digital filtering, swivel stand and available 4-20 mA output. |  | 9390 Battery Powered Weight Indicator
6-digit Unipolar display in a rugged NEMA 4X Stainless Steel washdown enclosure. Powers up to 4 load cells for portable and remote weighing applications. Standby mode for extended batter life. |  | HBM Weighing Electronics
HBM supplies weighing electronics for all industrial platform scales, truck or container scales. In addition HBM offers electronic systems for process automation, e.g. for checkweigher and dosing process. |  | UMC 600 Weight Indicator-Controller
The UMC600's rugged stainless steel design includes Batching and Weighing functions such as setpoints, preact and dribble control. Powers up to 8 350-ohm load cells. | | Weighing - Load Cells | |  | HBM Weighing Load Cells
Industrial production and scales constructions, production of building materials, food and consumer goods industries, pharmacy, and medical engineering... In almost all sectors where goods are produced, processed or controlled, HBM weighing technology components can be found. For the majority of HBM load cells official approval certificates are available. Appropriate certificates are also available for their worldwide use. All our standard load cells are also available for the various zone areas in accordance with the valid ATEX directive. | | Weighing - Single Point | |  | HBM Single Point Load Cells
The term platform scale nowadays covers a wide field of application in the industrial weighing technology. It covers the design and configuration of equipment such as high-precision laboratory balances, shop-counter scales and personal weighing machines right through to post office weighers, medical scales etc. Platform scales are characterised by one or more load cells, usually arranged under a platform (scale pan) on which the goods intended for weighing are placed. | | Weighing - Weigh Modules | |  | A4200 & A4600 Weighcheck Load Cells
Low profile load cell specifically designed for tank weighing where it is necessary to accommodate expansion and contraction of the tank. |
|
|
|
|
|
|
|